Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Linux on P2	SaucySoliton 2023-01-09 23:12	16	616	SaucySoliton 2023-03-23 06:43
Is there a better way to do this? 1 2	RossH 2023-03-05 01:23	36	578	evanh 2023-03-22 21:01
M.2 Standard and the P2	iseries 2023-03-12 16:12	9	404	Tubular 2023-03-15 22:29
Flash AND MicroSD in the same program - how to? / Flexprop	pik33 2022-11-26 15:25	27	547	hinv 2023-03-15 11:45
Single Sideband Transmitter 1 2	SaucySoliton 2023-02-21 00:19	36	1.1K	ManAtWork 2023-03-13 16:38
New REV C and REV D Power Requirements	iseries 2023-03-12 15:49	5	215	Ltech 2023-03-13 07:26
Goertzel mode? Where to find information?	JonTitus 2023-03-04 23:02	9	393	evanh 2023-03-13 00:39
Is a P2 Edge "Multi" Board feasible? 1 2	RossH 2023-02-28 00:36	37	612	evanh 2023-03-12 10:00
Debug vs. Smartpins while programming SPI interface [Solved]	Patrick1ab 2023-03-10 23:23	5	185	evanh 2023-03-11 23:31
Multimode SPI Implementation (SPIN2 + PASM) 1 2 3	greg_physics 2021-10-19 20:30	66	1.7K	evanh 2023-03-10 03:25
Why are there no P2 robots?	tempytempytemp 2023-02-27 22:47	13	519	knivd 2023-03-08 10:47
Adafruit ISM330DLC Gyro SPI P2 driver, yaw pitch roll rotation matrix integration, fixed and float	mwroberts 2023-03-05 19:42	1	294	ManAtWork 2023-03-06 09:16
Propeller Tool 2.9.3	jay_harlow 2023-02-22 21:18	8	385	jay_harlow 2023-03-03 19:35
CLKSET(NewCLKMODE, NewCLKFREQ) syntax question	Bob Drury 2021-11-20 01:01	26	472	pik33 2023-03-01 12:40
P2 under xray inspection	JRoark 2022-02-07 00:22	24	739	Tubular 2023-02-28 01:04
PC serial initialization - need to emulate Propeller Tool "Identify Hardware"?	technopol 2023-02-27 03:28	5	146	technopol 2023-02-27 21:55
2x6 Connectors on Edge accessory boards	ke4pjw 2023-02-23 23:38	15	242	ke4pjw 2023-02-26 03:51
2-Cog, 128KB-Hub, 32-I/O P2 1 2...6 7	cgracey 2018-10-09 02:11	189	4.5K	hinv 2023-02-19 16:39
XI = 4 MHz ?	TonyB_ 2023-02-17 12:28	1	122	evanh 2023-02-17 13:07
Super Tiny Fonts on the P2	cgracey 2023-01-31 23:55	14	507	ke4pjw 2023-02-16 01:58
propeller tool IDE	RS_Jim 2023-02-14 23:14	2	168	RS_Jim 2023-02-16 00:16
Struggling with the WX WiFi Module	jay_harlow 2022-11-20 00:48	16	425	__deets__ 2023-02-14 07:33
Working With CRC (Inline PASM2)	JonnyMac 2023-02-12 06:27	7	318	JonnyMac 2023-02-13 22:05
Only 30 mA per pin? (P1 has 40 mA per pin)	Rayman 2023-02-10 23:18	7	269	cgracey 2023-02-13 19:48
SPEC gas sensor for NO2 (and CO, alcohol, air quality, etc.)	Rayman 2023-02-06 19:45	11	290	SaucySoliton 2023-02-13 03:02
P2 - SD Boot Code (rev 2 silicon) 1 2	Cluso99 2019-10-18 22:09	31	1K	evanh 2023-02-11 11:55
Can I provide 1.2 V from a smart pin to switch a Solid State Relay (Sharp S202S02)	msrobots 2023-02-10 06:53	13	266	evanh 2023-02-11 00:52
P2 and GPS (SIM33EAU module)	ManAtWork 2023-02-08 14:51	4	186	Reinhard 2023-02-10 09:53
Multiple UART Interfacing Issue In P2	disha_sudra 2023-01-19 06:05	18	631	disha_sudra 2023-02-07 08:44
Is there an object pointer in Spin2?	jrullan 2022-11-28 03:17	23	506	avsa242 2023-02-05 00:38

Propeller 2

Discussion List