Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Serial Interface Concept	System 2023-08-24 19:12	5	79	knivd 2023-07-30 14:07
Question about p2asm and flexspin	Reinhard 2023-07-29 18:06	2	126	Reinhard 2023-07-29 18:55
P2 Edge Secure Holder?	jonyjib 2023-07-24 21:19	14	246	Mickster 2023-07-27 13:16
Getting arccosine and arctan using CORDIC functions	DiverBob 2021-03-02 04:18	25	1.2K	evanh 2023-07-24 01:06
Dead P2 Postmortem Questions	Duane Degn 2023-07-19 23:35	23	334	Rayman 2023-07-21 14:40
P2 Application Idea: Drive Step Motor with high Efficiency	Christof Eb. 2023-07-15 09:24	5	252	Christof Eb. 2023-07-20 14:06
Spin2 Code Generator (Work in Progress, most things working)	Rayman 2023-07-04 19:39	5	415	Rayman 2023-07-19 23:21
High frequency Stepper Motor driving	Mickster 2023-07-16 10:34	8	217	Mickster 2023-07-16 18:38
Tried following directions to get MicroPython running on a new P2 Edge/development board!	K6MLE 2023-07-13 00:37	10	194	rogloh 2023-07-14 04:49
P2 based Dog Bot walking (much better)	Rayman 2023-07-11 17:15	8	348	Rayman 2023-07-13 21:39
Newhaven 3.12" OLED display code in Spin2	Rayman 2023-04-06 20:46	6	451	hal2000 2023-07-07 14:08
upython w/o SD Card	Reinhard 2023-07-01 08:55	0	152	Reinhard 2023-07-01 08:55
P1 to P2 Migration	pilot0315 2023-05-19 23:31	30	891	pilot0315 2023-06-23 23:50
How to get restarted with P2?	frank freedman 2023-06-08 05:04	4	283	pilot0315 2023-06-19 13:43
IDE cannot communicate with Edge Module 1 2	JerryN 2023-05-30 17:14	46	611	evanh 2023-06-19 01:48
ADC driver for Spin2 with filtered Sinc2 and Sinc3 modes	Rayman 2023-06-11 21:59	7	350	evanh 2023-06-18 02:51
Anecdotal reliability of P2 in the heat	ke4pjw 2023-06-14 00:21	3	236	PropGuy2 2023-06-15 01:01
Unable to get Micropython to respond to terminal input 1 2 3 4	pedward 2023-05-31 03:30	98	958	pedward 2023-06-14 16:33
ADC voltage references	technopol 2023-06-11 03:35	6	301	technopol 2023-06-12 01:12
PropTool binary files	ozpropdev 2023-06-09 02:06	5	235	ozpropdev 2023-06-12 01:02
Asking the requisite "is there software to make the P2 into a Logic Analyzer" question again	pedward 2023-06-05 06:33	16	464	pedward 2023-06-07 03:10
YModem (over serial port) for P2	Rayman 2023-06-04 19:54	1	113	RossH 2023-06-04 23:50
ADC resolution	jaspast 2023-06-02 13:32	18	252	evanh 2023-06-03 05:22
Propeller P2 Edge module 3D models?	pedward 2023-05-31 06:20	9	278	pedward 2023-06-02 07:42
beginner trouble- LSM9DS1	jaspast 2023-06-01 02:49	8	197	JonnyMac 2023-06-02 02:16
Read / Write to microSD card on Edge?	jrullan 2023-05-31 14:58	9	245	jrullan 2023-05-31 23:05
How to boot from sdcard?	jrullan 2023-05-30 15:31	2	145	jrullan 2023-05-30 15:44
How to use external clock/crystal in P2?	disha_sudra 2023-05-19 13:00	11	326	evanh 2023-05-28 06:06
Waveshare touchscreens at 1024x600 and P2 HDMI/VGA	rogloh 2023-05-26 04:22	28	544	evanh 2023-05-27 12:50
Programming and developing for P2 from an rpi	moony 2021-01-15 14:40	26	1K	RS_Jim 2023-05-27 12:10

Propeller 2

Discussion List