Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
I2C Woes	9Escott 2024-01-26 21:23	8	305	VonSzarvas 2024-01-28 17:55
P2 Edges does Pan and Tilt with Gimbal	iseries 2020-12-24 14:31	9	309	cgracey 2024-01-28 00:35
Wiznet W6100 [was High(er) performing ethernet (W5300 or other)] 1 2 3 4	ke4pjw 2021-12-08 18:47	93	5.6K	ke4pjw 2024-01-26 02:42
composite video benefits with Propeller over digital VGA/HDMI 1 2	ngeneer 2024-01-18 18:38	35	702	evanh 2024-01-24 21:34
Updated 1080p 2bpp tiled VGA driver	Rayman 2023-12-30 23:27	8	452	Rayman 2024-01-24 17:05
DEBUG	3dogpottery 2024-01-18 20:16	15	448	3dogpottery 2024-01-24 13:04
QSPI driver for LAN9252 [solved] 1 2	ManAtWork 2023-12-19 16:00	48	1.2K	ManAtWork 2024-01-23 08:49
Experimental P2.spin?	3dogpottery 2024-01-13 13:27	22	453	3dogpottery 2024-01-22 14:20
FlexC and (non-) packed structs	ManAtWork 2022-12-29 18:16	15	297	ManAtWork 2024-01-22 12:54
frequency selection for _clkfreq	ngeneer 2024-01-21 06:04	4	172	ngeneer 2024-01-21 23:01
Power decoupling and P2 Edge	ke4pjw 2024-01-19 03:23	13	276	evanh 2024-01-21 01:12
1024-point FFT in 79 longs 1 2 3	cgracey 2019-12-17 15:27	75	3.1K	cgracey 2024-01-20 04:48
State machine vs. context switching	ManAtWork 2024-01-17 09:22	6	168	bob_g4bby 2024-01-17 13:03
P2 Driver for HUB75 LED Matrix Panels 1 2 3	Stephen Moraco 2020-10-14 23:58	75	6.4K	Wuerfel_21 2024-01-16 00:36
FlexSpin: is mixed HUB/LUT exec possible? (again)	ManAtWork 2024-01-14 18:37	9	205	evanh 2024-01-15 21:35
Alternative Oscillators to TG2520SMN	LMS 2024-01-14 10:04	5	189	Rayman 2024-01-14 23:17
P2-Stamp pre-launch samples 1 2...4 5	knivd 2023-07-04 14:30	124	2.4K	knivd 2024-01-13 14:52
VGA anti-aliasing issue	ti85 2024-01-11 17:25	7	342	Rayman 2024-01-12 20:25
Known good/bad uSD card types? 1 2 3	RossH 2023-12-22 23:29	69	1.1K	evanh 2024-01-11 05:15
Rapid "real-time" Audio Frequency Detection challenge 1 2	ngeneer 2024-01-01 11:44	54	1K	ngeneer 2024-01-09 02:35
NRF24L01+ revisited and other library issues 1 2 3 4	RS_Jim 2021-10-10 12:42	108	2.3K	RS_Jim 2024-01-06 11:55
6-axis arm as test tool - also pca9685 16 channel pwm board	Stephen Moraco 2021-08-14 23:15	7	426	SteffeD1 2024-01-04 10:10
Propeller IDE not working	bambino69 2024-01-03 02:57	3	130	bambino69 2024-01-03 03:12
Prop Tool issue with Mixed Cogexec and Hubexec	Rayman 2023-12-28 15:35	6	174	Rayman 2023-12-29 19:52
FTDI - Programmer on the edge 2 evaluation board	Nix 2023-12-24 00:02	3	265	Nix 2023-12-28 11:09
Christmas puzzle: SQI bit shuffler	ManAtWork 2023-12-23 15:34	6	218	ManAtWork 2023-12-28 10:06
Does __builtin_propeller_cogid() or cogid() work in flexprop for the P2?	MisterHemi 2023-12-27 04:34	3	159	MisterHemi 2023-12-27 10:29
Newbie Question: Using HUBSET in C	MisterHemi 2023-12-24 20:50	13	235	MisterHemi 2023-12-27 01:05
Debug coexisting with serial output?	Rayman 2023-12-02 15:52	17	375	Rayman 2023-12-25 19:57
Line following bot using low cost, Arducam, camera module (More or less working already)	Rayman 2023-11-16 21:02	20	681	Rayman 2023-12-25 15:44

Propeller 2

Discussion List