Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
mysterious ifdef/define error in FlexSpin	msrobots 2023-04-05 06:17	2	127	msrobots 2023-04-06 03:45
Wiznet official driver working (FlexC) (now with W6100 support!) 1 2 3	Rayman 2022-11-04 21:53	63	1.5K	Rayman 2023-04-05 16:28
Wiznet W5100/W5200 vs W6100	msrobots 2023-04-05 05:22	2	510	msrobots 2023-04-05 06:23
serial synchronous	pilot0315 2023-01-30 02:48	8	287	pilot0315 2023-04-03 16:20
Pin reading question	TonyB_ 2023-03-30 22:13	9	232	evanh 2023-04-01 05:03
Any interest in an 8 port WS2811/12 driver board?	ke4pjw 2023-04-01 04:57	0	88	ke4pjw 2023-04-01 04:57
Prop2 pipeline overview	evanh 2023-03-24 13:13	2	172	evanh 2023-03-30 11:30
Backfeeding the Edge development boards via 5V pin.	ke4pjw 2023-03-29 02:28	1	148	VonSzarvas 2023-03-29 11:49
Special price on P2 EVAL boards	VonSzarvas 2023-03-21 07:39	29	539	rogloh 2023-03-26 03:30
'nuther P2 Bytes the Dust... I think.	frank freedman 2023-03-25 17:25	4	199	frank freedman 2023-03-26 01:00
Smart pin modes 001001 (pulse/cycle output) or 001011 (transition output) for small frequencies.	aermosh 2023-03-24 08:59	15	256	aermosh 2023-03-25 20:35
Linux on P2	SaucySoliton 2023-01-09 23:12	16	710	SaucySoliton 2023-03-23 06:43
Is there a better way to do this? 1 2	RossH 2023-03-05 01:23	36	597	evanh 2023-03-22 21:01
M.2 Standard and the P2	iseries 2023-03-12 16:12	9	413	Tubular 2023-03-15 22:29
Flash AND MicroSD in the same program - how to? / Flexprop	pik33 2022-11-26 15:25	27	569	hinv 2023-03-15 11:45
Single Sideband Transmitter 1 2	SaucySoliton 2023-02-21 00:19	36	1.2K	ManAtWork 2023-03-13 16:38
New REV C and REV D Power Requirements	iseries 2023-03-12 15:49	5	229	Ltech 2023-03-13 07:26
Goertzel mode? Where to find information?	JonTitus 2023-03-04 23:02	9	433	evanh 2023-03-13 00:39
Is a P2 Edge "Multi" Board feasible? 1 2	RossH 2023-02-28 00:36	37	645	evanh 2023-03-12 10:00
Debug vs. Smartpins while programming SPI interface [Solved]	Patrick1ab 2023-03-10 23:23	5	194	evanh 2023-03-11 23:31
Multimode SPI Implementation (SPIN2 + PASM) 1 2 3	greg_physics 2021-10-19 20:30	66	1.8K	evanh 2023-03-10 03:25
Why are there no P2 robots?	tempytempytemp 2023-02-27 22:47	13	527	knivd 2023-03-08 10:47
Adafruit ISM330DLC Gyro SPI P2 driver, yaw pitch roll rotation matrix integration, fixed and float	mwroberts 2023-03-05 19:42	1	350	ManAtWork 2023-03-06 09:16
Propeller Tool 2.9.3	jay_harlow 2023-02-22 21:18	8	412	jay_harlow 2023-03-03 19:35
CLKSET(NewCLKMODE, NewCLKFREQ) syntax question	Bob Drury 2021-11-20 01:01	26	486	pik33 2023-03-01 12:40
P2 under xray inspection	JRoark 2022-02-07 00:22	24	750	Tubular 2023-02-28 01:04
PC serial initialization - need to emulate Propeller Tool "Identify Hardware"?	technopol 2023-02-27 03:28	5	177	technopol 2023-02-27 21:55
2x6 Connectors on Edge accessory boards	ke4pjw 2023-02-23 23:38	15	252	ke4pjw 2023-02-26 03:51
2-Cog, 128KB-Hub, 32-I/O P2 1 2...6 7	cgracey 2018-10-09 02:11	189	4.6K	hinv 2023-02-19 16:39
XI = 4 MHz ?	TonyB_ 2023-02-17 12:28	1	131	evanh 2023-02-17 13:07

Propeller 2

Discussion List