Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
frequency selection for _clkfreq	ngeneer 2024-01-21 06:04	4	157	ngeneer 2024-01-21 23:01
Power decoupling and P2 Edge	ke4pjw 2024-01-19 03:23	13	255	evanh 2024-01-21 01:12
1024-point FFT in 79 longs 1 2 3	cgracey 2019-12-17 15:27	75	2.9K	cgracey 2024-01-20 04:48
State machine vs. context switching	ManAtWork 2024-01-17 09:22	6	152	bob_g4bby 2024-01-17 13:03
P2 Driver for HUB75 LED Matrix Panels 1 2 3	Stephen Moraco 2020-10-14 23:58	75	4.8K	Wuerfel_21 2024-01-16 00:36
FlexSpin: is mixed HUB/LUT exec possible? (again)	ManAtWork 2024-01-14 18:37	9	185	evanh 2024-01-15 21:35
Alternative Oscillators to TG2520SMN	LMS 2024-01-14 10:04	5	176	Rayman 2024-01-14 23:17
P2-Stamp pre-launch samples 1 2...4 5	knivd 2023-07-04 14:30	124	2.2K	knivd 2024-01-13 14:52
VGA anti-aliasing issue	ti85 2024-01-11 17:25	7	297	Rayman 2024-01-12 20:25
Known good/bad uSD card types? 1 2 3	RossH 2023-12-22 23:29	69	1.1K	evanh 2024-01-11 05:15
Rapid "real-time" Audio Frequency Detection challenge 1 2	ngeneer 2024-01-01 11:44	54	912	ngeneer 2024-01-09 02:35
Can Goertzel mode do AM radio?	Rayman 2024-01-05 22:52	5	233	ManAtWork 2024-01-07 16:13
NRF24L01+ revisited and other library issues 1 2 3 4	RS_Jim 2021-10-10 12:42	108	2.2K	RS_Jim 2024-01-06 11:55
6-axis arm as test tool - also pca9685 16 channel pwm board	Stephen Moraco 2021-08-14 23:15	7	392	SteffeD1 2024-01-04 10:10
uSD Drivers FSRW and FAT32, both using same low level SPI drivers	Rayman 2023-06-03 18:06	23	463	Rayman 2024-01-03 22:31
Propeller IDE not working	bambino69 2024-01-03 02:57	3	111	bambino69 2024-01-03 03:12
Prop Tool issue with Mixed Cogexec and Hubexec	Rayman 2023-12-28 15:35	6	160	Rayman 2023-12-29 19:52
On-Board Flash File System 1 2 3 4	cgracey 2023-08-16 19:54	117	2.5K	Stephen Moraco 2023-12-28 23:40
FTDI - Programmer on the edge 2 evaluation board	Nix 2023-12-24 00:02	3	204	Nix 2023-12-28 11:09
Christmas puzzle: SQI bit shuffler	ManAtWork 2023-12-23 15:34	6	193	ManAtWork 2023-12-28 10:06
Does __builtin_propeller_cogid() or cogid() work in flexprop for the P2?	MisterHemi 2023-12-27 04:34	3	125	MisterHemi 2023-12-27 10:29
A retromachine Basic interpreter [beta] 1 2...6 7	pik33 2023-07-13 17:34	190	3.4K	Mickster 2023-12-27 02:36
Newbie Question: Using HUBSET in C	MisterHemi 2023-12-24 20:50	13	219	MisterHemi 2023-12-27 01:05
Debug coexisting with serial output?	Rayman 2023-12-02 15:52	17	355	Rayman 2023-12-25 19:57
Line following bot using low cost, Arducam, camera module (More or less working already)	Rayman 2023-11-16 21:02	20	616	Rayman 2023-12-25 15:44
KISS Eval board (general discussion) 1 2...7 8	ManAtWork 2020-09-30 08:14	224	7.6K	evanh 2023-12-24 00:13
3.4 MHz MCP23009 I2C I/O expander Spin2 Test (with SimplestSerial)	Rayman 2023-12-09 16:11	12	328	Rayman 2023-12-19 17:07
Dynamic memory allocation?	ManAtWork 2023-12-15 11:52	18	372	ManAtWork 2023-12-18 15:32
A question about connecting and programming P2 directly to RPi GPIO instead of USB	pik33 2023-12-16 21:47	4	118	Stephen Moraco 2023-12-16 23:08
C3-like dev board?	tempytempytemp 2023-11-28 11:07	18	606	Rayman 2023-12-15 15:17

Propeller 2

Discussion List