Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Getting Started With FlySky I-BUS 1 2	JonnyMac 2021-05-13 03:43	38	3.6K	ke4pjw 2023-04-17 17:53
Using FlexProp to help convert Spin2 to assembly	Rayman 2023-04-15 16:33	3	144	JonnyMac 2023-04-15 18:34
P2 COG Start!!	enorton 2023-04-14 17:31	5	244	enorton 2023-04-15 13:14
Official P2 display not working :(	__deets__ 2023-04-14 10:04	8	168	pik33 2023-04-15 08:11
Make Pin Output and Follow Input of Neighbor?	JonnyMac 2023-04-07 05:22	10	251	evanh 2023-04-08 12:28
P2 Start from other SD formats	frank freedman 2023-04-04 03:33	7	222	RichardB 2023-04-06 11:42
mysterious ifdef/define error in FlexSpin	msrobots 2023-04-05 06:17	2	140	msrobots 2023-04-06 03:45
Wiznet official driver working (FlexC) (now with W6100 support!) 1 2 3	Rayman 2022-11-04 21:53	63	1.5K	Rayman 2023-04-05 16:28
Wiznet W5100/W5200 vs W6100	msrobots 2023-04-05 05:22	2	522	msrobots 2023-04-05 06:23
serial synchronous	pilot0315 2023-01-30 02:48	8	294	pilot0315 2023-04-03 16:20
Pin reading question	TonyB_ 2023-03-30 22:13	9	237	evanh 2023-04-01 05:03
Any interest in an 8 port WS2811/12 driver board?	ke4pjw 2023-04-01 04:57	0	98	ke4pjw 2023-04-01 04:57
Prop2 pipeline overview	evanh 2023-03-24 13:13	2	175	evanh 2023-03-30 11:30
Backfeeding the Edge development boards via 5V pin.	ke4pjw 2023-03-29 02:28	1	151	VonSzarvas 2023-03-29 11:49
Special price on P2 EVAL boards	VonSzarvas 2023-03-21 07:39	29	547	rogloh 2023-03-26 03:30
'nuther P2 Bytes the Dust... I think.	frank freedman 2023-03-25 17:25	4	205	frank freedman 2023-03-26 01:00
Smart pin modes 001001 (pulse/cycle output) or 001011 (transition output) for small frequencies.	aermosh 2023-03-24 08:59	15	271	aermosh 2023-03-25 20:35
Is there a better way to do this? 1 2	RossH 2023-03-05 01:23	36	603	evanh 2023-03-22 21:01
M.2 Standard and the P2	iseries 2023-03-12 16:12	9	417	Tubular 2023-03-15 22:29
Flash AND MicroSD in the same program - how to? / Flexprop	pik33 2022-11-26 15:25	27	576	hinv 2023-03-15 11:45
Single Sideband Transmitter 1 2	SaucySoliton 2023-02-21 00:19	36	1.2K	ManAtWork 2023-03-13 16:38
New REV C and REV D Power Requirements	iseries 2023-03-12 15:49	5	231	Ltech 2023-03-13 07:26
Goertzel mode? Where to find information?	JonTitus 2023-03-04 23:02	9	451	evanh 2023-03-13 00:39
Is a P2 Edge "Multi" Board feasible? 1 2	RossH 2023-02-28 00:36	37	649	evanh 2023-03-12 10:00
Debug vs. Smartpins while programming SPI interface [Solved]	Patrick1ab 2023-03-10 23:23	5	195	evanh 2023-03-11 23:31
Multimode SPI Implementation (SPIN2 + PASM) 1 2 3	greg_physics 2021-10-19 20:30	66	1.9K	evanh 2023-03-10 03:25
Why are there no P2 robots?	tempytempytemp 2023-02-27 22:47	13	531	knivd 2023-03-08 10:47
Adafruit ISM330DLC Gyro SPI P2 driver, yaw pitch roll rotation matrix integration, fixed and float	mwroberts 2023-03-05 19:42	1	359	ManAtWork 2023-03-06 09:16
Propeller Tool 2.9.3	jay_harlow 2023-02-22 21:18	8	417	jay_harlow 2023-03-03 19:35
CLKSET(NewCLKMODE, NewCLKFREQ) syntax question	Bob Drury 2021-11-20 01:01	26	495	pik33 2023-03-01 12:40

Propeller 2

Discussion List