General Discussion

Primarily for questions regarding any Parallax product or general programming needs, and also friendly chatter.

Discussion	Started By	Replies	Views	Most Recent
Who went to the nextfest?	General Cedric 2008-10-11 21:55	1	440	General Cedric 2008-10-11 21:55
quick question on Nuts & Volts #125 (Control from your favorite terminal)	basicstampede 2008-10-10 16:25	8	976	basicstampede 2008-10-11 21:15
Lost part of form	sailman58 2008-10-08 02:05	7	1.2K	sailman58 2008-10-11 20:47
Unscribing From A Thread?	Bruce Bates 2008-10-11 14:40	5	992	Bruce Bates 2008-10-11 19:21
error	tpw_man 2008-10-11 01:27	3	927	RinksCustoms 2008-10-11 01:34
No Subject	paulmac 2008-09-30 11:13	4	1.1K	RinksCustoms 2008-10-11 01:03
Is a current sink the opposite of a current source?	po2le 2008-10-10 22:55	7	1.8K	Mike Green 2008-10-10 23:55
PCB software Comparisons 1 2	James Long 2008-01-19 04:08	35	3.7K	Lord Steve 2008-10-10 20:16
Emic indicating busy constantly after power- up	timex 2008-10-07 21:46	6	609	Chris Savage 2008-10-10 16:50
Edge detection	Rsadeika 2008-10-10 13:47	4	717	JonnyMac 2008-10-10 15:59
Slave I2C or UART ?	richaj45 2008-10-09 05:53	7	964	T&E Engineer 2008-10-10 11:49
Parallax - "Confusion"?	SRLM 2008-10-09 05:28	4	677	Phil Pilgrim (PhiPi) 2008-10-10 06:03
pololu motor controller	Badger 2008-10-10 02:09	6	504	Timmoore 2008-10-10 04:47
pololu motors specs	Badger 2008-10-10 04:05	1	512	Badger 2008-10-10 04:05
interrupt and shiftin/shiftout	Nraug Hmoob 2008-10-09 19:42	3	1K	Nraug Hmoob 2008-10-09 21:32
C & Spin translator needed	Erik Friesen 2008-10-09 01:50	8	882	Erik Friesen 2008-10-09 21:21
sony remote to control robot	davesky81 2008-10-08 00:11	3	947	LoopyByteloose 2008-10-09 17:07
Need a wireless serial cable solution.	T&E Engineer 2008-10-05 01:24	12	1.1K	RDL2004 2008-10-09 14:00
how to quit noisey motors	Badger 2008-10-08 23:05	9	887	PJAllen 2008-10-09 12:17
playing with SERIN	NR1X 2008-09-13 01:36	9	1.1K	NR1X 2008-10-09 01:23
environment noice	Erik 2008-10-09 00:05	5	816	Erik 2008-10-09 01:12
dual power supply -15 and 15 help	grasshopper 2008-10-07 14:48	16	4.4K	RDL2004 2008-10-08 16:46
Need UART VP to start sooner	openmic 2008-10-07 21:50	2	1.2K	Peter Verkaik 2008-10-08 08:23
What do you use to solder on?	Ken Gracey 2008-10-03 21:42	25	3.4K	SRLM 2008-10-08 06:17
powering a servo	Lee Marshall 2008-10-03 23:39	8	928	Lee Marshall 2008-10-08 00:56
Advice on using 9v battery	T Chap 2006-09-05 07:06	28	5K	Macgman2000 2008-10-07 23:12
Multi-alarms clock project	Gumby 2008-09-29 20:59	5	875	Gumby 2008-10-07 18:03
USB Datalogger Design	SRLM 2008-10-06 04:53	7	998	Tracy Allen 2008-10-07 16:14
Shift Register to ULN2803	Tim-M 2008-10-06 22:22	3	1.1K	Tim-M 2008-10-06 22:28
Eagle software and the ground	grasshopper 2008-10-06 19:50	3	937	grasshopper 2008-10-06 20:03

General Discussion

Discussion List