General Discussion

Primarily for questions regarding any Parallax product or general programming needs, and also friendly chatter.

Discussion	Started By	Replies	Views	Most Recent
Unscribing From A Thread?	Bruce Bates 2008-10-11 14:40	5	988	Bruce Bates 2008-10-11 19:21
error	tpw_man 2008-10-11 01:27	3	923	RinksCustoms 2008-10-11 01:34
No Subject	paulmac 2008-09-30 11:13	4	1.1K	RinksCustoms 2008-10-11 01:03
Is a current sink the opposite of a current source?	po2le 2008-10-10 22:55	7	1.8K	Mike Green 2008-10-10 23:55
PCB software Comparisons 1 2	James Long 2008-01-19 04:08	35	3.6K	Lord Steve 2008-10-10 20:16
Emic indicating busy constantly after power- up	timex 2008-10-07 21:46	6	608	Chris Savage 2008-10-10 16:50
Edge detection	Rsadeika 2008-10-10 13:47	4	715	JonnyMac 2008-10-10 15:59
Slave I2C or UART ?	richaj45 2008-10-09 05:53	7	958	T&E Engineer 2008-10-10 11:49
Parallax - "Confusion"?	SRLM 2008-10-09 05:28	4	673	Phil Pilgrim (PhiPi) 2008-10-10 06:03
pololu motor controller	Badger 2008-10-10 02:09	6	501	Timmoore 2008-10-10 04:47
pololu motors specs	Badger 2008-10-10 04:05	1	508	Badger 2008-10-10 04:05
interrupt and shiftin/shiftout	Nraug Hmoob 2008-10-09 19:42	3	1K	Nraug Hmoob 2008-10-09 21:32
C & Spin translator needed	Erik Friesen 2008-10-09 01:50	8	878	Erik Friesen 2008-10-09 21:21
sony remote to control robot	davesky81 2008-10-08 00:11	3	943	LoopyByteloose 2008-10-09 17:07
Need a wireless serial cable solution.	T&E Engineer 2008-10-05 01:24	12	1.1K	RDL2004 2008-10-09 14:00
how to quit noisey motors	Badger 2008-10-08 23:05	9	885	PJAllen 2008-10-09 12:17
playing with SERIN	NR1X 2008-09-13 01:36	9	1.1K	NR1X 2008-10-09 01:23
environment noice	Erik 2008-10-09 00:05	5	810	Erik 2008-10-09 01:12
dual power supply -15 and 15 help	grasshopper 2008-10-07 14:48	16	4.4K	RDL2004 2008-10-08 16:46
Need UART VP to start sooner	openmic 2008-10-07 21:50	2	1.2K	Peter Verkaik 2008-10-08 08:23
What do you use to solder on?	Ken Gracey 2008-10-03 21:42	25	3.3K	SRLM 2008-10-08 06:17
powering a servo	Lee Marshall 2008-10-03 23:39	8	924	Lee Marshall 2008-10-08 00:56
Advice on using 9v battery	T Chap 2006-09-05 07:06	28	5K	Macgman2000 2008-10-07 23:12
Multi-alarms clock project	Gumby 2008-09-29 20:59	5	873	Gumby 2008-10-07 18:03
USB Datalogger Design	SRLM 2008-10-06 04:53	7	997	Tracy Allen 2008-10-07 16:14
Shift Register to ULN2803	Tim-M 2008-10-06 22:22	3	1.1K	Tim-M 2008-10-06 22:28
Eagle software and the ground	grasshopper 2008-10-06 19:50	3	931	grasshopper 2008-10-06 20:03
Chris Savage....did you come across the joystick..	deno 2008-09-28 12:03	11	1.5K	Chris Savage 2008-10-06 19:12
Fault-tolerant systems	Leon 2008-10-04 10:37	20	1.6K	Jo 2008-10-06 15:47
What is an easy way to write a two switch Lock out routine for a piece Equipmen	sam_sam_sam 2008-09-30 01:30	9	757	hippy 2008-10-06 11:04

General Discussion

Discussion List