Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Empty Block Error (Gets In The Way)	JonnyMac 2020-03-08 20:01	4	212	ErNa 2020-03-09 09:49
CRC8	JonnyMac 2020-03-07 19:02	23	535	Roy Eltham 2020-03-09 02:05
P2 programming using real COM port?	TonyB_ 2020-02-29 12:26	30	758	wmosscrop 2020-03-07 15:08
ECC memory	Rayman 2020-03-07 03:05	7	203	Electrodude 2020-03-07 04:21
Companion parts for Prop 2 1 2 3	jmg 2013-07-02 21:06	90	8.8K	evanh 2020-03-06 09:20
Proposed external & HyperRAM memory interface suitable for video drivers with other COGs. 1 2 3	rogloh 2019-10-21 01:29	73	1.3K	evanh 2020-03-05 06:32
high speed labeler application	veluxllc 2020-02-29 01:02	14	431	veluxllc 2020-03-04 14:25
P2 definition for KICAD library	JRoark 2020-02-14 21:34	17	655	evanh 2020-03-01 11:05
Stepper motor control	ManAtWork 2020-02-29 13:58	6	213	ManAtWork 2020-02-29 15:38
Best route to develop on the new P2, which hardware do I go for? 1 2	Coley 2020-02-16 11:48	31	850	evanh 2020-02-27 20:29
Smartpin questions - undocumented	rogloh 2020-02-27 02:55	13	215	evanh 2020-02-27 06:26
Can you use interrupts with hubexec?	Rayman 2020-02-25 23:25	19	397	evanh 2020-02-26 23:35
Switching a cog from WAITATN triggered to ATTENTION INTERRUPT triggered	Rayman 2020-02-25 19:20	8	134	Rayman 2020-02-25 21:20
CALL problem with PNut binaries	bradzone 2020-01-20 16:45	8	325	cgracey 2020-02-25 09:14
Pure PASM2 in Propeller Tool and FlexGui?	Rayman 2020-02-24 13:54	4	150	cgracey 2020-02-24 15:16
TESTB and Z flag	ManAtWork 2020-02-24 08:22	3	163	cgracey 2020-02-24 14:31
P1 Spin for P2	Cluso99 2018-06-02 04:05	8	495	Roy Eltham 2020-02-24 06:29
Formatting the P2 instructions spreadsheet	Peter Jakacki 2020-02-04 04:03	19	687	Cluso99 2020-02-24 03:18
USB serial	msrobots 2020-02-22 10:30	18	367	octetta 2020-02-23 18:11
Something rather strange in Pulse/Cycle Smartpin mode output 1 2 3	rogloh 2020-02-18 12:05	87	1.3K	rogloh 2020-02-22 23:44
P2ES Rev B red LED & Could not find a P2 on port /dev/cu.usbserial-... 1 2	dgately 2020-02-12 18:50	36	773	JRoark 2020-02-18 21:22
Spin2: Get Specific Byte from Word or Long?	JonnyMac 2020-02-16 23:42	30	447	Ariba 2020-02-18 01:23
XBYTE and hardware stack	TonyB_ 2020-02-15 12:19	15	405	TonyB_ 2020-02-18 00:41
Make PNut A Little More Friendly?	JonnyMac 2020-02-16 23:53	4	240	JonnyMac 2020-02-17 01:53
Waiting for a Smartpin output/completion state in the P2	rogloh 2020-02-16 23:55	5	151	AJL 2020-02-17 01:38
HDMI Specification Question for P2 1 2	MSwann 2020-01-28 02:11	31	1.3K	pilot0315 2020-02-15 19:28
P2 - Where will it be used? It's time for Parallax to step up and answer this!	Cluso99 2020-02-15 07:07	7	298	Dave Hein 2020-02-15 19:21
P2 QDIV/QFRAC Clarification Needed	MSwann 2020-01-12 20:30	6	266	pilot0315 2020-02-13 07:26
SAL shift arithmetic left	ManAtWork 2020-02-10 17:22	24	581	ManAtWork 2020-02-12 08:21
Single step debugger?	ManAtWork 2020-02-11 08:50	8	213	ManAtWork 2020-02-11 13:01

Propeller 2

Discussion List