Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Switching a cog from WAITATN triggered to ATTENTION INTERRUPT triggered	Rayman 2020-02-25 19:20	8	129	Rayman 2020-02-25 21:20
CALL problem with PNut binaries	bradzone 2020-01-20 16:45	8	320	cgracey 2020-02-25 09:14
Pure PASM2 in Propeller Tool and FlexGui?	Rayman 2020-02-24 13:54	4	148	cgracey 2020-02-24 15:16
TESTB and Z flag	ManAtWork 2020-02-24 08:22	3	161	cgracey 2020-02-24 14:31
P1 Spin for P2	Cluso99 2018-06-02 04:05	8	495	Roy Eltham 2020-02-24 06:29
Formatting the P2 instructions spreadsheet	Peter Jakacki 2020-02-04 04:03	19	683	Cluso99 2020-02-24 03:18
USB serial	msrobots 2020-02-22 10:30	18	362	octetta 2020-02-23 18:11
Something rather strange in Pulse/Cycle Smartpin mode output 1 2 3	rogloh 2020-02-18 12:05	87	1.2K	rogloh 2020-02-22 23:44
P2ES Rev B red LED & Could not find a P2 on port /dev/cu.usbserial-... 1 2	dgately 2020-02-12 18:50	36	761	JRoark 2020-02-18 21:22
Spin2: Get Specific Byte from Word or Long?	JonnyMac 2020-02-16 23:42	30	440	Ariba 2020-02-18 01:23
XBYTE and hardware stack	TonyB_ 2020-02-15 12:19	15	391	TonyB_ 2020-02-18 00:41
Make PNut A Little More Friendly?	JonnyMac 2020-02-16 23:53	4	239	JonnyMac 2020-02-17 01:53
Waiting for a Smartpin output/completion state in the P2	rogloh 2020-02-16 23:55	5	150	AJL 2020-02-17 01:38
HDMI Specification Question for P2 1 2	MSwann 2020-01-28 02:11	31	1.2K	pilot0315 2020-02-15 19:28
P2 - Where will it be used? It's time for Parallax to step up and answer this!	Cluso99 2020-02-15 07:07	7	296	Dave Hein 2020-02-15 19:21
P2 QDIV/QFRAC Clarification Needed	MSwann 2020-01-12 20:30	6	265	pilot0315 2020-02-13 07:26
SAL shift arithmetic left	ManAtWork 2020-02-10 17:22	24	575	ManAtWork 2020-02-12 08:21
Single step debugger?	ManAtWork 2020-02-11 08:50	8	211	ManAtWork 2020-02-11 13:01
Calculation of arcus tangens	Reinhard 2020-02-05 11:48	19	462	Reinhard 2020-02-10 12:10
P2 Touchscreen + Memory	cheezus 2018-09-30 06:27	30	1.8K	cheezus 2020-02-09 06:20
External Ram	msrobots 2020-02-08 03:04	4	221	JRoark 2020-02-09 03:23
p1 and p2 PASM TUTORIAL	pilot0315 2019-07-14 03:22	30	1.3K	pilot0315 2020-02-08 23:10
P2 Ethernet 1 2	JohnC 2019-10-03 16:47	31	1.7K	ke4pjw 2020-02-06 19:17
Park transformation for motor control	ManAtWork 2020-02-05 15:12	14	491	Wuerfel_21 2020-02-06 16:05
Good way to do Jump table in PASM2?	Rayman 2020-02-01 00:16	8	286	Rayman 2020-02-05 14:48
Good way to do table indexing?	ManAtWork 2020-02-04 09:56	8	225	evanh 2020-02-05 00:15
Smartpin adc value question	CRST1 2020-01-19 00:55	9	216	evanh 2020-02-03 22:36
Question about cogs, dacs and pins	Reinhard 2020-01-30 12:13	15	405	evanh 2020-02-02 08:57
Anyone used SETPAT & WAITPAT ?	Cluso99 2019-03-01 02:40	20	532	AJL 2020-02-01 22:32
July Morning -- intro--	Reinhard 2020-02-01 22:10	0	114	Reinhard 2020-02-01 22:10

Propeller 2

Discussion List