Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Stepper motor control	ManAtWork 2020-02-29 13:58	6	196	ManAtWork 2020-02-29 15:38
Best route to develop on the new P2, which hardware do I go for? 1 2	Coley 2020-02-16 11:48	31	843	evanh 2020-02-27 20:29
Smartpin questions - undocumented	rogloh 2020-02-27 02:55	13	199	evanh 2020-02-27 06:26
Can you use interrupts with hubexec?	Rayman 2020-02-25 23:25	19	382	evanh 2020-02-26 23:35
Switching a cog from WAITATN triggered to ATTENTION INTERRUPT triggered	Rayman 2020-02-25 19:20	8	129	Rayman 2020-02-25 21:20
CALL problem with PNut binaries	bradzone 2020-01-20 16:45	8	314	cgracey 2020-02-25 09:14
Pure PASM2 in Propeller Tool and FlexGui?	Rayman 2020-02-24 13:54	4	141	cgracey 2020-02-24 15:16
TESTB and Z flag	ManAtWork 2020-02-24 08:22	3	156	cgracey 2020-02-24 14:31
P1 Spin for P2	Cluso99 2018-06-02 04:05	8	489	Roy Eltham 2020-02-24 06:29
Formatting the P2 instructions spreadsheet	Peter Jakacki 2020-02-04 04:03	19	674	Cluso99 2020-02-24 03:18
USB serial	msrobots 2020-02-22 10:30	18	353	octetta 2020-02-23 18:11
Something rather strange in Pulse/Cycle Smartpin mode output 1 2 3	rogloh 2020-02-18 12:05	87	1.2K	rogloh 2020-02-22 23:44
P2ES Rev B red LED & Could not find a P2 on port /dev/cu.usbserial-... 1 2	dgately 2020-02-12 18:50	36	751	JRoark 2020-02-18 21:22
Spin2: Get Specific Byte from Word or Long?	JonnyMac 2020-02-16 23:42	30	439	Ariba 2020-02-18 01:23
XBYTE and hardware stack	TonyB_ 2020-02-15 12:19	15	380	TonyB_ 2020-02-18 00:41
Make PNut A Little More Friendly?	JonnyMac 2020-02-16 23:53	4	230	JonnyMac 2020-02-17 01:53
Waiting for a Smartpin output/completion state in the P2	rogloh 2020-02-16 23:55	5	143	AJL 2020-02-17 01:38
HDMI Specification Question for P2 1 2	MSwann 2020-01-28 02:11	31	1.1K	pilot0315 2020-02-15 19:28
P2 - Where will it be used? It's time for Parallax to step up and answer this!	Cluso99 2020-02-15 07:07	7	296	Dave Hein 2020-02-15 19:21
P2 QDIV/QFRAC Clarification Needed	MSwann 2020-01-12 20:30	6	258	pilot0315 2020-02-13 07:26
SAL shift arithmetic left	ManAtWork 2020-02-10 17:22	24	556	ManAtWork 2020-02-12 08:21
Single step debugger?	ManAtWork 2020-02-11 08:50	8	204	ManAtWork 2020-02-11 13:01
Calculation of arcus tangens	Reinhard 2020-02-05 11:48	19	454	Reinhard 2020-02-10 12:10
P2 Touchscreen + Memory	cheezus 2018-09-30 06:27	30	1.8K	cheezus 2020-02-09 06:20
External Ram	msrobots 2020-02-08 03:04	4	213	JRoark 2020-02-09 03:23
p1 and p2 PASM TUTORIAL	pilot0315 2019-07-14 03:22	30	1.3K	pilot0315 2020-02-08 23:10
P2 Ethernet 1 2	JohnC 2019-10-03 16:47	31	1.7K	ke4pjw 2020-02-06 19:17
Park transformation for motor control	ManAtWork 2020-02-05 15:12	14	475	Wuerfel_21 2020-02-06 16:05
Good way to do Jump table in PASM2?	Rayman 2020-02-01 00:16	8	271	Rayman 2020-02-05 14:48
Good way to do table indexing?	ManAtWork 2020-02-04 09:56	8	215	evanh 2020-02-05 00:15

Propeller 2

Discussion List