Propeller 2

Primary purpose is for early adopters of Propeller 2, for the creation of programming tools, and for documentation development.

Discussion	Started By	Replies	Views	Most Recent
Using 64GB SDHC/SDXC "exFAT" cards with the P2 and TAQOZ	Peter Jakacki 2019-02-20 12:25	1	239	Cluso99 2019-02-20 17:35
stupid questions about PASM2	msrobots 2019-02-18 23:29	6	202	msrobots 2019-02-19 07:09
AUGS not cancelling after a ALTD instruction	ozpropdev 2019-02-16 23:16	8	342	cgracey 2019-02-19 06:09
One more clock delay on next silicon inputs 1 2 3	cgracey 2019-02-07 02:44	73	1.4K	jmg 2019-02-19 00:44
VGA 1920x1080x4bpp @148.5MHz - Rock Stable and 240 chars x 135 lines :) 1 2...5 6	Cluso99 2018-11-17 00:12	169	5.8K	cgracey 2019-02-18 07:01
Pnut arrays?	kbash 2019-02-14 18:09	9	310	kbash 2019-02-17 16:27
XORO32 scrambler output	evanh 2019-01-13 06:34	29	589	TonyB_ 2019-02-17 13:07
About the upcoming P2	samuell 2019-02-16 17:07	7	341	samuell 2019-02-17 02:15
Feedback Servo (example of setting up PASM2 cog)	tomcrawford 2019-02-15 22:27	2	150	Mark_T 2019-02-16 01:32
Access to CNT register	tomcrawford 2019-02-15 18:57	4	211	Cluso99 2019-02-16 00:21
SETQ - Quick question for Chip	Cluso99 2019-02-15 09:40	7	151	Cluso99 2019-02-15 12:05
AUGS/AUGD queries	TonyB 2017-04-28 14:37	18	496	TonyB_ 2019-02-15 11:37
Will hub FIFO abuse be consistent across FPGA, P2-ES, P2 final, etc.?	Electrodude 2019-02-15 00:27	3	166	msrobots 2019-02-15 10:41
P2 (circa 2013) versus 1st working silicon	Rayman 2019-02-13 23:32	1	210	cgracey 2019-02-13 23:56
Instructions that inject results into the next instruction	Seairth 2019-02-12 00:41	24	439	msrobots 2019-02-13 06:51
PLL fix possibly found	cgracey 2019-02-09 07:11	29	1.3K	SaucySoliton 2019-02-13 03:14
D/S PASM	John Abshier 2019-02-10 16:42	4	191	Rayman 2019-02-10 18:39
P2 Tooling Installation via nix for AnyLinux™ (any Linux Distribution)	__red__ 2019-01-13 20:11	22	559	__red__ 2019-02-10 01:22
Breakouts for P2 Eval 1 2 3	Rayman 2018-12-29 14:56	73	2.9K	Tubular 2019-02-07 06:42
Understanding pins better (or at all)	cheezus 2019-02-03 23:00	8	494	jmg 2019-02-06 23:49
P2 Mailbox and Parameters - where to place and what is needed? 1 2	Cluso99 2019-02-02 01:22	46	722	ersmith 2019-02-04 12:28
Reading the state of a smartpin	Peter Jakacki 2019-02-03 06:50	6	146	ozpropdev 2019-02-03 09:23
SD boot problem ???	Cluso99 2019-02-02 04:33	4	185	Cluso99 2019-02-02 17:44
ROM changes for next silicon... 1 2	Cluso99 2019-01-30 13:52	31	952	msrobots 2019-02-02 00:33
REP blocks and branching issue.	ozpropdev 2018-12-18 03:50	21	485	cgracey 2019-02-01 11:47
Testing P2 at + 10% / - 5% voltage specs	Tubular 2019-02-01 03:20	3	142	ozpropdev 2019-02-01 09:40
P2 Eval --> Microsoft Serial BallPoint?	Rayman 2019-01-30 22:37	10	1.7K	Rayman 2019-01-31 15:02
My first Spin2 Program Fails	John Abshier 2019-01-29 20:55	10	370	rosco_pc 2019-01-31 09:02
P2 Pull-up detection	Cluso99 2019-01-31 03:57	0	119	Cluso99 2019-01-31 03:57
Collatz: Uses conditional JMP within REP block	tomcrawford 2019-01-28 17:13	4	292	evanh 2019-01-31 00:22

Propeller 2

Discussion List