Propeller 1

Propeller 1 discussion for all applications, hobby or commercial.

Discussion	Started By	Replies	Views	Most Recent
PropellerIDE 123456789.spin (NOT FOUND) ?!?	courtens 2015-05-30 11:58	2	287	evanh 2015-05-30 15:52
ssd 1963	pilot0315 2015-05-30 15:12	1	272	pilot0315 2015-05-30 15:12
Multicore problem. processes do not run parallel	ErgoBot 2015-05-29 03:34	4	442	JonnyMac 2015-05-29 11:56
Using Simple IDE without aboard to program	plau45 2015-05-29 07:30	4	236	yeti 2015-05-29 08:26
PropEtcherPropeller-controlled Etch-a-sketch	mpark 2010-02-01 15:52	28	5.2K	idbruce 2015-05-29 06:24
OpenSpin 1.00.77 Now with Unused Method Removal	Roy Eltham 2015-05-19 02:16	8	851	Roy Eltham 2015-05-29 02:13
Steppers Hopefully Producing Circular Motion	Duane Degn 2015-05-27 15:10	9	444	kwinn 2015-05-28 10:37
Parallel Programmer Considerations	Kye 2015-05-21 08:33	8	858	Kye 2015-05-27 17:22
Trouble using I2C	Boblow45 2014-10-16 14:01	4	585	Saravanan 2015-05-27 13:31
programming a propeller with another propeller	dr hydra 2015-05-26 08:35	13	1.2K	Peter Jakacki 2015-05-27 06:22
VGA "Not Supported Mode" on a Samsung TV	Genetix 2015-04-23 12:14	13	2.3K	Genetix 2015-05-26 17:01
Square root methods	Peter Jakacki 2015-05-20 09:13	18	1.6K	Peter Jakacki 2015-05-26 07:27
Programming a propeller dip with raspberry pi gpio	dr hydra 2015-05-24 12:59	2	324	Heater. 2015-05-24 13:14
Driving an analog gauge with a small stepper directly from the Propeller	JohnR2010 2015-05-20 09:34	27	5.2K	AJM 2015-05-23 13:03
Another i2c assembly driver	Rayman 2015-05-15 06:20	14	1.6K	tomcrawford 2015-05-23 09:34
power on the propeller project board	dr hydra 2014-02-10 08:09	7	889	dr hydra 2015-05-21 19:46
propeller-load -q what is "status"?	DavidZemon 2015-05-21 08:15	4	472	DavidZemon 2015-05-21 11:51
Debug and explore your hardware the easy way! 1 2	Peter Jakacki 2015-01-08 22:52	49	5.2K	Peter Jakacki 2015-05-20 23:50
Propeller Clock Speed	hippy 2007-09-08 18:24	17	2.9K	JohnR2010 2015-05-20 11:46
Powersupply Boost Converter based on the TI TPS6120x	JohnR2010 2015-05-19 06:13	10	826	JohnR2010 2015-05-20 11:30
Propeller-GCC 1_9_0 GDB	jazzed 2015-04-29 09:14	11	1.2K	ersmith 2015-05-19 04:47
ESP8266 Huzzah	DavidZemon 2015-05-17 15:39	17	1.8K	localroger 2015-05-18 14:52
ActivityBot Programming	chuck l 2015-05-16 14:29	3	578	chuck l 2015-05-17 16:49
MCP3202: SPI D[out] through 300 ohm resistor? And decoupling question(s)	mmgood 2015-05-12 14:07	5	704	Alexander (Sandy) Hapgood 2015-05-16 16:45
Bus Communications	Discovery 2015-05-13 14:49	9	575	DavidZemon 2015-05-16 09:56
New Attempt - 3D Printer Controller And Firmware 1 2...4 5	idbruce 2015-04-09 10:23	127	8.4K	idbruce 2015-05-16 06:28
P1V Hub 4x faster 1:4 (4 cogs), 2x 1:8 (8 cogs) + new compile options	Cluso99 2015-04-05 16:50	29	3.3K	Cluso99 2015-05-15 01:49
Open Propeller Project #8: Eddie Firmware Ported to Propeller Activity Board 1 2 3	Ken Gracey 2014-11-03 17:50	67	53.4K	Duane Degn 2015-05-14 10:57
Quickstart board and raspberry pi	dr hydra 2015-05-13 07:52	5	438	dr hydra 2015-05-14 10:44
Booting .eeprom files from SD cards	Phil Pilgrim (PhiPi) 2015-05-13 13:37	10	775	Phil Pilgrim (PhiPi) 2015-05-14 09:45

Propeller 1

Discussion List