Shop OBEX P1 Docs P2 Docs Learn Events
need help w/ pololu 16 servo? — Parallax Forums

need help w/ pololu 16 servo?

ArchiverArchiver Posts: 46,084
edited 2003-11-17 16:35 in General Discussion
Does any one know how to make a servo move using the SEROUT command
to communicate to the pololu 16 servo controller? Any thing would be
appreciated!

Anthony

Comments

  • ArchiverArchiver Posts: 46,084
    edited 2003-11-17 16:10
    Try this?

    http://www.pololu.com/products/pololu/0290/ssc02a_guide.pdf

    [noparse]:)[/noparse]

    --
    Vern Graner CNE/CNA/SSE | "If the network is down, then you're
    Senior Systems Engineer | obviously incompetent so why are we
    Texas Information Services | paying you? Of course, if the network
    http://www.txis.com | is up, then we obviously don't need
    Austin Office 512 328-8947 | you, so why are we paying you?" VLG




    ihockeyfan88 said:
    > Does any one know how to make a servo move using the SEROUT command
    > to communicate to the pololu 16 servo controller? Any thing would be
    > appreciated!
    >
    > Anthony
    >
    >
    >
    > To UNSUBSCRIBE, just send mail to:
    > basicstamps-unsubscribe@yahoogroups.com
    > from the same email address that you subscribed. Text in the Subject and
    > Body of the message will be ignored.
    >
    >
    > Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
    >
    >
    >
  • ArchiverArchiver Posts: 46,084
    edited 2003-11-17 16:35
    Hmm after a few minutes of looking around, it seems thatthe PDF file only
    has assembly instructions and operating parameters, HOWEVER, there is an
    intersting note in their DOCS:

    "This servo controller is also compatible with the Scott Edwards MiniSSC
    II servo controller and any software written for it."

    So, just go have a look for example code for the SSCII from
    http://www.seetron.com or http://www.parallax.com

    Vern

    --
    Vern Graner CNE/CNA/SSE | "If the network is down, then you're
    Senior Systems Engineer | obviously incompetent so why are we
    Texas Information Services | paying you? Of course, if the network
    http://www.txis.com | is up, then we obviously don't need
    Austin Office 512 328-8947 | you, so why are we paying you?" VLG




    Vernon Graner said:
    > Try this?
    >
    > http://www.pololu.com/products/pololu/0290/ssc02a_guide.pdf
    >
    > [noparse]:)[/noparse]
    >
    > --
    > Vern Graner CNE/CNA/SSE | "If the network is down, then you're
    > Senior Systems Engineer | obviously incompetent so why are we
    > Texas Information Services | paying you? Of course, if the network
    > http://www.txis.com | is up, then we obviously don't need
    > Austin Office 512 328-8947 | you, so why are we paying you?" VLG
    >
    >
    >
    >
    > ihockeyfan88 said:
    >> Does any one know how to make a servo move using the SEROUT command
    >> to communicate to the pololu 16 servo controller? Any thing would be
    >> appreciated!
    >>
    >> Anthony
    >>
    >>
    >>
    >> To UNSUBSCRIBE, just send mail to:
    >> basicstamps-unsubscribe@yahoogroups.com
    >> from the same email address that you subscribed. Text in the Subject
    >> and
    >> Body of the message will be ignored.
    >>
    >>
    >> Your use of Yahoo! Groups is subject to
    >> http://docs.yahoo.com/info/terms/
    >>
    >>
    >>
    >
    >
    > To UNSUBSCRIBE, just send mail to:
    > basicstamps-unsubscribe@yahoogroups.com
    > from the same email address that you subscribed. Text in the Subject and
    > Body of the message will be ignored.
    >
    >
    > Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
    >
    >
    >
Sign In or Register to comment.