Shop OBEX P1 Docs P2 Docs Learn Events
ROV Code available — Parallax Forums

ROV Code available

ArchiverArchiver Posts: 46,084
edited 2003-09-03 18:05 in General Discussion
I have a lot of BS2sx code, but I don't know how useful it would be
to anyone else's project, except for some QBasic code which works on
a laptop which is connected to the stamp. It waits for serial sensor
data from the stamp, and then gives a graphical display of that data.
It shows a picture of the ROV's tilt, roll, compass heading, and
depth. also if a certain bit is set in the transmission to the
laptop, the laptop reads in from a 'mission.txt' file, and then sends
these values to the stamp. This was done to allow autonomous control
of the ROV (laptop reads premade plans, sends the mission steps to
the stamp one at a time). If you want that code, I've put it in the
file section in the ROV folder.

Comments

  • ArchiverArchiver Posts: 46,084
    edited 2003-09-02 17:27
    Sam:

    Couldn't find your posted software code.

    Dick
    Original Message
    From: Sam <hard-on@t...>
    To: <basicstamps@yahoogroups.com>
    Sent: Thursday, August 28, 2003 11:19 AM
    Subject: [noparse][[/noparse]basicstamps] ROV Code available


    > I have a lot of BS2sx code, but I don't know how useful it would be
    > to anyone else's project, except for some QBasic code which works on
    > a laptop which is connected to the stamp. It waits for serial sensor
    > data from the stamp, and then gives a graphical display of that data.
    > It shows a picture of the ROV's tilt, roll, compass heading, and
    > depth. also if a certain bit is set in the transmission to the
    > laptop, the laptop reads in from a 'mission.txt' file, and then sends
    > these values to the stamp. This was done to allow autonomous control
    > of the ROV (laptop reads premade plans, sends the mission steps to
    > the stamp one at a time). If you want that code, I've put it in the
    > file section in the ROV folder.
    >
    >
    > To UNSUBSCRIBE, just send mail to:
    > basicstamps-unsubscribe@yahoogroups.com
    > from the same email address that you subscribed. Text in the Subject and
    Body of the message will be ignored.
    >
    >
    > Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
    >
    >
  • ArchiverArchiver Posts: 46,084
    edited 2003-09-03 15:39
    it's in the ROV pics folder

    --- In basicstamps@yahoogroups.com, "Richard Gurske" <rfgurske@i...>
    wrote:
    > Sam:
    >
    > Couldn't find your posted software code.
    >
    > Dick
    >
    >
    Original Message
    > From: Sam <hard-on@t...>
    > To: <basicstamps@yahoogroups.com>
    > Sent: Thursday, August 28, 2003 11:19 AM
    > Subject: [noparse][[/noparse]basicstamps] ROV Code available
    >
    >
    > > I have a lot of BS2sx code, but I don't know how useful it would
    be
    > > to anyone else's project, except for some QBasic code which works
    on
    > > a laptop which is connected to the stamp. It waits for serial
    sensor
    > > data from the stamp, and then gives a graphical display of that
    data.
    > > It shows a picture of the ROV's tilt, roll, compass heading, and
    > > depth. also if a certain bit is set in the transmission to the
    > > laptop, the laptop reads in from a 'mission.txt' file, and then
    sends
    > > these values to the stamp. This was done to allow autonomous
    control
    > > of the ROV (laptop reads premade plans, sends the mission steps to
    > > the stamp one at a time). If you want that code, I've put it in
    the
    > > file section in the ROV folder.
    > >
    > >
    > > To UNSUBSCRIBE, just send mail to:
    > > basicstamps-unsubscribe@yahoogroups.com
    > > from the same email address that you subscribed. Text in the
    Subject and
    > Body of the message will be ignored.
    > >
    > >
    > > Your use of Yahoo! Groups is subject to
    http://docs.yahoo.com/info/terms/
    > >
    > >
  • ArchiverArchiver Posts: 46,084
    edited 2003-09-03 18:05
    Well, the QBasic code is there, but the BS2 code isn't.

    --- In basicstamps@yahoogroups.com, "Sam" <hard-on@t...> wrote:
    > it's in the ROV pics folder
    >
    > --- In basicstamps@yahoogroups.com, "Richard Gurske"
    <rfgurske@i...>
    > wrote:
    > > Sam:
    > >
    > > Couldn't find your posted software code.
    > >
    > > Dick
    > >
    > >
    Original Message
    > > From: Sam <hard-on@t...>
    > > To: <basicstamps@yahoogroups.com>
    > > Sent: Thursday, August 28, 2003 11:19 AM
    > > Subject: [noparse][[/noparse]basicstamps] ROV Code available
    > >
    > >
    > > > I have a lot of BS2sx code, but I don't know how useful it
    would
    > be
    > > > to anyone else's project, except for some QBasic code which
    works
    > on
    > > > a laptop which is connected to the stamp. It waits for serial
    > sensor
    > > > data from the stamp, and then gives a graphical display of that
    > data.
    > > > It shows a picture of the ROV's tilt, roll, compass heading, and
    > > > depth. also if a certain bit is set in the transmission to the
    > > > laptop, the laptop reads in from a 'mission.txt' file, and then
    > sends
    > > > these values to the stamp. This was done to allow autonomous
    > control
    > > > of the ROV (laptop reads premade plans, sends the mission steps
    to
    > > > the stamp one at a time). If you want that code, I've put it in
    > the
    > > > file section in the ROV folder.
    > > >
    > > >
    > > > To UNSUBSCRIBE, just send mail to:
    > > > basicstamps-unsubscribe@yahoogroups.com
    > > > from the same email address that you subscribed. Text in the
    > Subject and
    > > Body of the message will be ignored.
    > > >
    > > >
    > > > Your use of Yahoo! Groups is subject to
    > http://docs.yahoo.com/info/terms/
    > > >
    > > >
Sign In or Register to comment.