Motor Control question
Archiver
Posts: 46,084
Has anyone used a L293DNE chip from Texas Instruments with a BS2? I found one in
an old computer tape drive and would like to implement it into my next robot as
a driver for 2 12VDC gear motors. Thanks for any info or past expiriences.
John
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
[noparse][[/noparse]Non-text portions of this message have been removed]
an old computer tape drive and would like to implement it into my next robot as
a driver for 2 12VDC gear motors. Thanks for any info or past expiriences.
John
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
[noparse][[/noparse]Non-text portions of this message have been removed]
Comments
jim
http://www.geocities.com/jimforkin2003/
Original Message
From: John Baker [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=L-z-z8Lz3A5R9MgFl8ePNN9EE1DcYS43aQNEq9WXU8vr8yajJ2WC0UpdvwiceGRlvokXunacEy2r9zObdNphxxQfOQ]johnbaker_erie_pa@y...[/url
Sent: Wednesday, August 20, 2003 1:54 PM
To: basicstamps@yahoogroups.com
Subject: [noparse][[/noparse]basicstamps] Motor Control question
Has anyone used a L293DNE chip from Texas Instruments with a BS2? I found
one in an old computer tape drive and would like to implement it into my
next robot as a driver for 2 12VDC gear motors. Thanks for any info or past
expiriences.
John
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
[noparse][[/noparse]Non-text portions of this message have been removed]
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Jim Forkin <jjf@p...> wrote:An alternative to drive two gear motors with
the basic stamp:
jim
http://www.geocities.com/jimforkin2003/
Original Message
From: John Baker [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=lLFES5RuhLCGFXZMYbvADDzGZ_-NnNhbRNQjtit4m01HwEpcp56DZL7BppNXIRAlAGou9pAlAmnPpqQBDCzQP-48du2y]johnbaker_erie_pa@y...[/url
Sent: Wednesday, August 20, 2003 1:54 PM
To: basicstamps@yahoogroups.com
Subject: [noparse][[/noparse]basicstamps] Motor Control question
Has anyone used a L293DNE chip from Texas Instruments with a BS2? I found
one in an old computer tape drive and would like to implement it into my
next robot as a driver for 2 12VDC gear motors. Thanks for any info or past
expiriences.
John
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
[noparse][[/noparse]Non-text portions of this message have been removed]
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject and Body of
the message will be ignored.
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
Do you Yahoo!?
SBC Yahoo! DSL - Now only $29.95 per month!
[noparse][[/noparse]Non-text portions of this message have been removed]