Debug question
Archiver
Posts: 46,084
I was looking in the documentation and can't find where the baud rate
of the programming and debug function are specified. I have a LCD and
have it hooked up to see the debug statement and need to set it's baud
rate to the stamp's.
I looked at using a P out pin for serout, but it looked less simple<G>.
of the programming and debug function are specified. I have a LCD and
have it hooked up to see the debug statement and need to set it's baud
rate to the stamp's.
I looked at using a P out pin for serout, but it looked less simple<G>.
Comments
you want to connect to a terminal at a different baud rate, use SEROUT
and SERIN.
-- Jon Williams
-- Applications Engineer, Parallax
-- Dallas Office
Original Message
From: Grover Richardson [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=BWDp-KJGfpmYb7DJuYgA8icoMzioigoQG_DuvyvUmDuKiZvQN37U1TJ_6qOaiPniBMwJSC0arHGf8V46NbiYrC8pW81Q8DuMrw]grover.richardson@g...[/url
Sent: Friday, August 15, 2003 9:58 AM
To: basicstamps@yahoogroups.com
Subject: [noparse][[/noparse]basicstamps] Debug question
I was looking in the documentation and can't find where the baud rate
of the programming and debug function are specified. I have a LCD and
have it hooked up to see the debug statement and need to set it's baud
rate to the stamp's.
I looked at using a P out pin for serout, but it looked less simple<G>.
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject
and Body of the message will be ignored.
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
This message has been scanned by WebShield. Please report SPAM to
abuse@p....
grover.richardson@g... writes:
I was looking in the documentation and can't find where the baud rate
of the programming and debug function are specified. I have a LCD and
have it hooked up to see the debug statement and need to set it's baud
rate to the stamp's.
Baud rate for the Stamp is set within the Stamp. This baud rate is
automatically used by the LCD serout commands. Baud rate for the debug screen
is
selected in the debug window. Look near the top of the debug window.
Sid Weaver
W4EKQ
Port Richey, FL
[noparse][[/noparse]Non-text portions of this message have been removed]
PBASIC manual. Unless you're writing a secondary loader (like the
Stache) it's not important. That said, the programming protocol --
including baud -- is covered in the material documentation that come
with the compiled tokenzer modules (for advanced programmers who want to
create their own editor).
The baud rate of DEBUG is covered in the manual on page 105.
-- Jon Williams
-- Applications Engineer, Parallax
-- Dallas Office
Original Message
From: Newzed@a... [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=BbMkbAN7N6XGAXZlsj7kdQjGx1VDMG3AJi6lc5Zdpq6cAbc4660H_i8aVStIbX7KZvDnjEQ]Newzed@a...[/url
Sent: Friday, August 15, 2003 10:16 AM
To: basicstamps@yahoogroups.com
Subject: [noparse][[/noparse]basicstamps] Debug Question
In a message dated 8/15/2003 11:03:42 AM Eastern Standard Time,
grover.richardson@g... writes:
I was looking in the documentation and can't find where the baud rate of
the programming and debug function are specified. I have a LCD and have
it hooked up to see the debug statement and need to set it's baud rate
to the stamp's.
Baud rate for the Stamp is set within the Stamp. This baud rate is
automatically used by the LCD serout commands. Baud rate for the debug
screen is
selected in the debug window. Look near the top of the debug window.
Sid Weaver
W4EKQ
Port Richey, FL
[noparse][[/noparse]Non-text portions of this message have been removed]
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject
and Body of the message will be ignored.
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
This message has been scanned by WebShield. Please report SPAM to
abuse@p....
Many thanks!!
Original Message
From: Jon Williams [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=UOu7Jqdcx7M59ziMi_QDnyb-Q_qH1nlts-TC3NLNagUhnKJEOmF8VgF0Gzltwr3GNoYd5xIBnaR6LnK46qr3]jwilliams@p...[/url
Sent: Friday, August 15, 2003 1:32 PM
To: basicstamps@yahoogroups.com
Subject: RE: [noparse][[/noparse]basicstamps] Debug Question
I'm not sure if the downloading baud speed is actually discussed in the
PBASIC manual. Unless you're writing a secondary loader (like the
Stache) it's not important. That said, the programming protocol --
including baud -- is covered in the material documentation that come
with the compiled tokenzer modules (for advanced programmers who want to
create their own editor).
The baud rate of DEBUG is covered in the manual on page 105.
-- Jon Williams
-- Applications Engineer, Parallax
-- Dallas Office
Original Message
From: Newzed@a... [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=Iii1KbDIFW2x8oJHmC_z0FN2w4Qxyili4j2JZM6dYlwPpT7UPblk32AQs3A018scQziz-0z1EcJm]Newzed@a...[/url
Sent: Friday, August 15, 2003 10:16 AM
To: basicstamps@yahoogroups.com
Subject: [noparse][[/noparse]basicstamps] Debug Question
In a message dated 8/15/2003 11:03:42 AM Eastern Standard Time,
grover.richardson@g... writes:
I was looking in the documentation and can't find where the baud rate of
the programming and debug function are specified. I have a LCD and have
it hooked up to see the debug statement and need to set it's baud rate
to the stamp's.
Baud rate for the Stamp is set within the Stamp. This baud rate is
automatically used by the LCD serout commands. Baud rate for the debug
screen is
selected in the debug window. Look near the top of the debug window.
Sid Weaver
W4EKQ
Port Richey, FL
[noparse][[/noparse]Non-text portions of this message have been removed]
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject
and Body of the message will be ignored.
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
This message has been scanned by WebShield. Please report SPAM to
abuse@p....
To UNSUBSCRIBE, just send mail to:
basicstamps-unsubscribe@yahoogroups.com
from the same email address that you subscribed. Text in the Subject
and Body of the message will be ignored.
Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/