program posted for tesing out roswell clone motors
Archiver
Posts: 46,084
http://www.inetport.com/~davisele/roswell.html
I posted my program to control (test) the motors on the roswell clone.
It is already compiled. just download it to the chip.
also if you turn the monitor port on (19200) you will see the 4 channels of
data going to the
PWM co-processor.
Richard
I posted my program to control (test) the motors on the roswell clone.
It is already compiled. just download it to the chip.
also if you turn the monitor port on (19200) you will see the 4 channels of
data going to the
PWM co-processor.
Richard
Comments
ended up being the inputs were picking up noise.
so isolate inputs,try to run code with out inputs and test code.
also try software debounce on inputs.
hope this helps some.
victor
Original Message
From: "Richard Friedrich" <rfriedrich@a...>
To: <basicstamps@yahoogroups.com>; <basicx@yahoogroups.com>
Sent: Tuesday, August 28, 2001 11:30 AM
Subject: [noparse][[/noparse]basicstamps] program posted for tesing out roswell clone motors
> http://www.inetport.com/~davisele/roswell.html
>
> I posted my program to control (test) the motors on the roswell clone.
> It is already compiled. just download it to the chip.
> also if you turn the monitor port on (19200) you will see the 4 channels
of
> data going to the
> PWM co-processor.
>
>
>
> Richard
>
>
>
>
>
>
> To UNSUBSCRIBE, just send mail to:
> basicstamps-unsubscribe@yahoogroups.com
> from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
responded to wrong message
victor
Original Message
From: "victor Faria" <victorf@g...>
To: <basicstamps@yahoogroups.com>; <basicx@yahoogroups.com>
Sent: Tuesday, August 28, 2001 6:38 PM
Subject: Re: [noparse][[/noparse]basicstamps] program posted for tesing out roswell clone
motors
> I had a similar problem.
> ended up being the inputs were picking up noise.
> so isolate inputs,try to run code with out inputs and test code.
> also try software debounce on inputs.
> hope this helps some.
> victor
>
Original Message
> From: "Richard Friedrich" <rfriedrich@a...>
> To: <basicstamps@yahoogroups.com>; <basicx@yahoogroups.com>
> Sent: Tuesday, August 28, 2001 11:30 AM
> Subject: [noparse][[/noparse]basicstamps] program posted for tesing out roswell clone motors
>
>
> > http://www.inetport.com/~davisele/roswell.html
> >
> > I posted my program to control (test) the motors on the roswell clone.
> > It is already compiled. just download it to the chip.
> > also if you turn the monitor port on (19200) you will see the 4 channels
> of
> > data going to the
> > PWM co-processor.
> >
> >
> >
> > Richard
> >
> >
> >
> >
> >
> >
> > To UNSUBSCRIBE, just send mail to:
> > basicstamps-unsubscribe@yahoogroups.com
> > from the same email address that you subscribed. Text in the Subject
and
> Body of the message will be ignored.
> >
> >
> > Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
> >
> >
>
>
> To UNSUBSCRIBE, just send mail to:
> basicstamps-unsubscribe@yahoogroups.com
> from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>