Programming Error FIXED!
Archiver
Posts: 46,084
FOUND IT!
I thought i had my genuine parallax cable..........DOH!
Original Message
From: <mhr_54@h...>
To: <basicstamps@yahoogroups.com>
Sent: Thursday, July 26, 2001 5:17 AM
Subject: [noparse][[/noparse]basicstamps] Re: Fw: Programming Error
> --- In basicstamps@y..., "Tim Stockman, STOCKMAN ELECTRONICS"
> <stocky@c...> wrote:
> >
> >
Original Message
> > From: Tim Stockman, STOCKMAN ELECTRONICS
> > To: basicstamps@y...
> > Sent: Wednesday, July 25, 2001 8:37 AM
> > Subject: Programming Error
> >
> >
> > Stampers,
> >
> > Just trying to program my first BS2e.
> >
> > It tokenizes OK, but gives me a "hardware communication" error
> when it gets to the download part.
> > What could be wrong?
> >
> > Current setup:-
> > - Genuine BS2 serial cable being used
> > - Stamp powered by regulated 5v supply
> > - Cap in ATN line
> > - Compaq Contura 410 Notebook (programs other serial devices no
> probs!)
> >
> >
> > Stocky
> >
> >
> > [noparse][[/noparse]Non-text portions of this message have been removed]
>
> ______________________________________________________________________
>
> Stocky,
>
> Do you have a palm pilot with hotsync loaded on your computer?
> If so it can cause these sorts of errors and make the stamp software
> think it can't get to the stamp.
> If you do have palm pilot or hotsync e-mail me asap at
> mhr_54@h...
>
> Sincerely,
> mhr_54
>
>
> To UNSUBSCRIBE, just send mail to:
> basicstamps-unsubscribe@yahoogroups.com
> from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
I thought i had my genuine parallax cable..........DOH!
Original Message
From: <mhr_54@h...>
To: <basicstamps@yahoogroups.com>
Sent: Thursday, July 26, 2001 5:17 AM
Subject: [noparse][[/noparse]basicstamps] Re: Fw: Programming Error
> --- In basicstamps@y..., "Tim Stockman, STOCKMAN ELECTRONICS"
> <stocky@c...> wrote:
> >
> >
Original Message
> > From: Tim Stockman, STOCKMAN ELECTRONICS
> > To: basicstamps@y...
> > Sent: Wednesday, July 25, 2001 8:37 AM
> > Subject: Programming Error
> >
> >
> > Stampers,
> >
> > Just trying to program my first BS2e.
> >
> > It tokenizes OK, but gives me a "hardware communication" error
> when it gets to the download part.
> > What could be wrong?
> >
> > Current setup:-
> > - Genuine BS2 serial cable being used
> > - Stamp powered by regulated 5v supply
> > - Cap in ATN line
> > - Compaq Contura 410 Notebook (programs other serial devices no
> probs!)
> >
> >
> > Stocky
> >
> >
> > [noparse][[/noparse]Non-text portions of this message have been removed]
>
> ______________________________________________________________________
>
> Stocky,
>
> Do you have a palm pilot with hotsync loaded on your computer?
> If so it can cause these sorts of errors and make the stamp software
> think it can't get to the stamp.
> If you do have palm pilot or hotsync e-mail me asap at
> mhr_54@h...
>
> Sincerely,
> mhr_54
>
>
> To UNSUBSCRIBE, just send mail to:
> basicstamps-unsubscribe@yahoogroups.com
> from the same email address that you subscribed. Text in the Subject and
Body of the message will be ignored.
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>