Serial Ram?
Archiver
Posts: 46,084
RE: [noparse][[/noparse]basicstamps] IR Communication
I have used the 24LCXX serries EEProm quite often in the past. I am looking for a RAM solution that uses a simular 2 wire interface. Can anyone point me in the right direction? Thank you.
MH
Original Message
From: Babu, Nagi -*Contractor
To: 'basicstamps@egroups.com'
Sent: Monday, October 23, 2000 6:38 AM
Subject: RE: [noparse][[/noparse]basicstamps] IR Communication
Hey Paul,
Where can I find more info on your book ? and what is a SASE (sorry I did not get that word - I guess I took off too early from school when they were covering that section of english [noparse]:)[/noparse]
thanks Paul
nagi
Original Message
From: Paul Verhage [noparse]/noparse][url=mailto:pverhage@sd131.k12.id.us]mailto[noparse]:p[/noparse]verhage@sd131.k12.id.us[/url
Sent: Monday, October 23, 2000 8:34 AM
To: 'basicstamps@egroups.com'
Subject: RE: [noparse][[/noparse]basicstamps] IR Communication
I've got a PCB designed to use the GP as an IR Proximity Detector.· It's
also a part of my BS/L book.· Send me a SASE and I'll send you a PCB to try
out.
Paul
I'm just not able to nail this thing down. I'm following the application
note #11 in the Basic Stamp Manual (in the Stamp I section). I bought Radio
Shack's 276-137 (GP1U52X).
I'm not able to figure why the receiver is not able to receive the values
from the transmitter. I do not know if the transmitter is working at all in
the first place.
Please advise, the following is what I've got.
Any help is greatly appreciated.
Thanks a lot in advance.
nagi
I have used the 24LCXX serries EEProm quite often in the past. I am looking for a RAM solution that uses a simular 2 wire interface. Can anyone point me in the right direction? Thank you.
MH
Original Message
From: Babu, Nagi -*Contractor
To: 'basicstamps@egroups.com'
Sent: Monday, October 23, 2000 6:38 AM
Subject: RE: [noparse][[/noparse]basicstamps] IR Communication
Hey Paul,
Where can I find more info on your book ? and what is a SASE (sorry I did not get that word - I guess I took off too early from school when they were covering that section of english [noparse]:)[/noparse]
thanks Paul
nagi
Original Message
From: Paul Verhage [noparse]/noparse][url=mailto:pverhage@sd131.k12.id.us]mailto[noparse]:p[/noparse]verhage@sd131.k12.id.us[/url
Sent: Monday, October 23, 2000 8:34 AM
To: 'basicstamps@egroups.com'
Subject: RE: [noparse][[/noparse]basicstamps] IR Communication
I've got a PCB designed to use the GP as an IR Proximity Detector.· It's
also a part of my BS/L book.· Send me a SASE and I'll send you a PCB to try
out.
Paul
I'm just not able to nail this thing down. I'm following the application
note #11 in the Basic Stamp Manual (in the Stamp I section). I bought Radio
Shack's 276-137 (GP1U52X).
I'm not able to figure why the receiver is not able to receive the values
from the transmitter. I do not know if the transmitter is working at all in
the first place.
Please advise, the following is what I've got.
Any help is greatly appreciated.
Thanks a lot in advance.
nagi