Please Remove Us
Archiver
Posts: 46,084
Please remove the church from your onelist.
Thank you,
Theresa Romig
Memorial United Methodist Church Secretary
Paton Dave-A13593 wrote:
>
> JR has been in the RC business since I can remember. Their stuff is durable
> worst case, and IMHO one of the best choices out there (HiTec/RCD's FET
> servos are up there too).
>
> -dave
>
> Dave Paton Motorola Advanced Technology Center
> voice 847.538.7575 pager 888.773.6802
> A13593@e...
>
> >
Original Message
> > From: ED Ward [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=fsqrSYZwV1nsmbIwNyNTgPBA48pvyrdvOS8tOBInnh9oX0BMf1i5PkTq0ng_JIm8MNtJBVa5-PNyz2L0cgnq]punk__rocker@h...[/url
> > Sent: Sunday, July 16, 2000 11:41 PM
> > To: basicstamps@egroups.com
> > Subject: [noparse][[/noparse]basicstamps] JR servos
> >
> >
> > Does any one have experience with these? I am thinking of
> > purchasing some
> > JR517s (ball bearing) to make a 12 servo hexapod. Are these
> > suitable? I
> > can get a good deal on them, they cost $45 new, and I can
> > get them for $30
> > new. These are Canadian prices. The typical american price
> > is $27. I
> > believe that they are high quality, but am not quite sure.
> > I'm not looking
> > for comparison on specs. I have found those already. As
> > with any other
> > products, some manufactures will over rate their stuff and
> > other will under
> > rate it, but I won't get into that now. I want to know if they are
> > reliable, durable, smooth (being ball bearing I assume they
> > are), and long
> > lasting. CAn anyone offer some advice?
> > ______________________________________________________________
> > __________
> > Get Your Private, Free E-mail from MSN Hotmail at
> http://www.hotmail.com
Thank you,
Theresa Romig
Memorial United Methodist Church Secretary
Paton Dave-A13593 wrote:
>
> JR has been in the RC business since I can remember. Their stuff is durable
> worst case, and IMHO one of the best choices out there (HiTec/RCD's FET
> servos are up there too).
>
> -dave
>
> Dave Paton Motorola Advanced Technology Center
> voice 847.538.7575 pager 888.773.6802
> A13593@e...
>
> >
Original Message
> > From: ED Ward [noparse]/noparse]mailto:[url=http://forums.parallaxinc.com/group/basicstamps/post?postID=fsqrSYZwV1nsmbIwNyNTgPBA48pvyrdvOS8tOBInnh9oX0BMf1i5PkTq0ng_JIm8MNtJBVa5-PNyz2L0cgnq]punk__rocker@h...[/url
> > Sent: Sunday, July 16, 2000 11:41 PM
> > To: basicstamps@egroups.com
> > Subject: [noparse][[/noparse]basicstamps] JR servos
> >
> >
> > Does any one have experience with these? I am thinking of
> > purchasing some
> > JR517s (ball bearing) to make a 12 servo hexapod. Are these
> > suitable? I
> > can get a good deal on them, they cost $45 new, and I can
> > get them for $30
> > new. These are Canadian prices. The typical american price
> > is $27. I
> > believe that they are high quality, but am not quite sure.
> > I'm not looking
> > for comparison on specs. I have found those already. As
> > with any other
> > products, some manufactures will over rate their stuff and
> > other will under
> > rate it, but I won't get into that now. I want to know if they are
> > reliable, durable, smooth (being ball bearing I assume they
> > are), and long
> > lasting. CAn anyone offer some advice?
> > ______________________________________________________________
> > __________
> > Get Your Private, Free E-mail from MSN Hotmail at
> http://www.hotmail.com