Shop OBEX P1 Docs P2 Docs Learn Events
ColorPAL won't stop flashing color — Parallax Forums

ColorPAL won't stop flashing color

jacquelinevl03jacquelinevl03 Posts: 18
edited 2017-01-08 17:44 in BASIC Stamp
Help!! I want to program the ColorPAL sensor, but it won't stop flashing light. I ran sample programs on the ColorPAL, but now they don't seem to stop. Please help, I would like to detect color, not flash color.


Thank you

This is the code that I think keeps running. The ColorPAL keeps flashing colors even though I did run the program, or even if it is not connected to Pin15. As long as it has power it flashes colors.

' =========================================================================
'
' File...... ColorPAL_flicker.bs2
' Purpose... ColorPAL flickering candle imitator.
' Author.... Phil Pilgrim -- Bueno Systems, Inc.
' E-mail.... propeller@phipi.com
' Started... 17 Apr 2009
' Updated... 26 Jan 2010: Changed reset delay from 50 ms. to 80ms.
'
' {$STAMP BS2}
' {$PBASIC 2.5}
'
' =========================================================================

'
[ Program Description ]

' This program programs the ColorPAL to imitate a flickering candle.
' Once programmed, it will run standalone with just +5V and ground
' connections.

'
[ I/O Definitions ]

sio PIN 15 ' Serial I/O com pin for ColorPAL.

'
[ Constants ]

' Baudrate definitions. Serial I/O must be open-drain. The ColorPAL includes
' a pullup internally.

#SELECT $STAMP
#CASE BS2, BS2E, BS2PE
baud CON 119 + 32768
#CASE BS2SX, BS2P
baud CON 327 + 32768
#CASE BS2PX
baud CON 536 + 32768
#ENDSELECT

'
[ Variables ]

red VAR Word ' Received RGB values from ColorPAL.
grn VAR Word
blu VAR Word

'
[ Initialization ]

GOSUB Reset ' Reset the ColorPAL and enter direct command mode.

'
[ Program Code ]

SEROUT sio, baud, ["= (00 ?05 Y t09 F t05 r404000 t09 ) #00"]
PAUSE 1000
SEROUT sio, baud, ["!"]
DO:LOOP

'
[ Subroutines ]

' Reset: Sends a long break to reset ColorPAL and enter direct command mode.

Reset:
LOW sio 'Pull sio low to eliminate any residual charge.
INPUT sio 'Return pin to input.
DO UNTIL sio : LOOP 'Wait for pin to be pulled high by ColorPAL.
LOW sio 'Pull pin low.
PAUSE 80 'Keep low for 80ms to enter Direct mode.
INPUT sio 'Return pin to input.
PAUSE 10 'Pause another 10ms
RETURN

Comments

  • PublisonPublison Posts: 12,366
    Welcome to the forums!

    Could you post the code that you are using that creates the problem?

  • jacquelinevl03jacquelinevl03 Posts: 18
    ' =========================================================================
    '
    ' File...... ColorPAL_flicker.bs2
    ' Purpose... ColorPAL flickering candle imitator.
    ' Author.... Phil Pilgrim -- Bueno Systems, Inc.
    ' E-mail.... propeller@phipi.com
    ' Started... 17 Apr 2009
    ' Updated... 26 Jan 2010: Changed reset delay from 50 ms. to 80ms.
    '
    ' {$STAMP BS2}
    ' {$PBASIC 2.5}
    '
    ' =========================================================================

    '
    [ Program Description ]

    ' This program programs the ColorPAL to imitate a flickering candle.
    ' Once programmed, it will run standalone with just +5V and ground
    ' connections.

    '
    [ I/O Definitions ]

    sio PIN 15 ' Serial I/O com pin for ColorPAL.

    '
    [ Constants ]

    ' Baudrate definitions. Serial I/O must be open-drain. The ColorPAL includes
    ' a pullup internally.

    #SELECT $STAMP
    #CASE BS2, BS2E, BS2PE
    baud CON 119 + 32768
    #CASE BS2SX, BS2P
    baud CON 327 + 32768
    #CASE BS2PX
    baud CON 536 + 32768
    #ENDSELECT

    '
    [ Variables ]

    red VAR Word ' Received RGB values from ColorPAL.
    grn VAR Word
    blu VAR Word

    '
    [ Initialization ]

    GOSUB Reset ' Reset the ColorPAL and enter direct command mode.

    '
    [ Program Code ]

    SEROUT sio, baud, ["= (00 ?05 Y t09 F t05 r404000 t09 ) #00"]
    PAUSE 1000
    SEROUT sio, baud, ["!"]
    DO:LOOP

    '
    [ Subroutines ]

    ' Reset: Sends a long break to reset ColorPAL and enter direct command mode.

    Reset:
    LOW sio 'Pull sio low to eliminate any residual charge.
    INPUT sio 'Return pin to input.
    DO UNTIL sio : LOOP 'Wait for pin to be pulled high by ColorPAL.
    LOW sio 'Pull pin low.
    PAUSE 80 'Keep low for 80ms to enter Direct mode.
    INPUT sio 'Return pin to input.
    PAUSE 10 'Pause another 10ms
    RETURN
  • jacquelinevl03jacquelinevl03 Posts: 18
    I think it keeps running this flicker program. Even if the ColorPAL is not connected to Pin15 it keeps on running. As long as it has power it keeps on flashing and I do not know how to make it stop flashing, so that I can sense colors with the ColorPAL sensor.
  • PublisonPublison Posts: 12,366
    edited 2017-01-08 18:34
    jacquelinevl03 wrote: »
    I think it keeps running this flicker program. Even if the ColorPAL is not connected to Pin15 it keeps on running. As long as it has power it keeps on flashing and I do not know how to make it stop flashing, so that I can sense colors with the ColorPAL sensor.

    When you run a program on the BS2, it is save to the EEPROM on the chip. Every time you power up, it will run that program. To make it stop flashing, and sense colors, you need to load another program in the Basic Stamp Tool, such as the programs found here:

    https://www.parallax.com/downloads/colorpal-color-matching-program-and-basic-stamp-sample-files



  • jacquelinevl03jacquelinevl03 Posts: 18
    Those are the programs I have downloaded, when I run the sense program from that zip file it still flashes the colors.
  • PublisonPublison Posts: 12,366
    Have you tried to program the BS2 with the ColorPAL_sense.bs2?

    zip
    zip
    28380-ColorPAL-Color-Matching-Program-BS-Sample-Files (5).zip
    2M
  • Phil Pilgrim (PhiPi)Phil Pilgrim (PhiPi) Posts: 23,514
    edited 2017-01-08 21:30
    Just to be clear, when you run, say, colorPAL_sense.bs2, with the ColorPAL and P15 connected, it still flickers? With the sense program running, it will still produce continuous flashes of color so it can read the RGB components. But you should see output in your DEBUG screen.

    -Phil
  • jacquelinevl03jacquelinevl03 Posts: 18
    When I run the colorPAL_sense.bs2 with the ColorPAL and P15 connected, as you said, it flickers green, yellow, and red light. When I run the program the debugger window does pop up, so I put a green paper in front of the ColorPAL and the DEBUG screen does not give me any output.
  • jacquelinevl03jacquelinevl03 Posts: 18
    I believe I have the exact same problem as kazuya86.
    http://forums.parallax.com/discussion/157618/colorpal-28380
    I tried your solution to him Phil Pilgrim, but it gave me the error of: "Expected a constant, variable, unary operator, or ("
  • jacquelinevl03jacquelinevl03 Posts: 18
    Publison,
    Yes, that is the program I am using.
  • Phil Pilgrim (PhiPi)Phil Pilgrim (PhiPi) Posts: 23,514
    jacquelinevl03 wrote:
    I tried your solution to him Phil Pilgrim, but it gave me the error of: "Expected a constant, variable, unary operator, or ("

    Which line of the program gives you this error?

    -Phil
  • jacquelinevl03jacquelinevl03 Posts: 18
    SEROUT sio, baud, SEROUT sio, baud, ["= #00"]
    When it gives out the error code it highlights the second SEROUT.
    Phil Pilgrim (PhiPi) wrote: »
    jacquelinevl03 wrote:
    I tried your solution to him Phil Pilgrim, but it gave me the error of: "Expected a constant, variable, unary operator, or ("

    Which line of the program gives you this error?

    -Phil

    error.JPG
    1274 x 697 - 91K
  • Phil Pilgrim (PhiPi)Phil Pilgrim (PhiPi) Posts: 23,514
    Somehow a second SEROUT sio, baud, got duplicated in that line. Just delete it.

    -Phil
  • jacquelinevl03jacquelinevl03 Posts: 18
    edited 2017-01-29 01:13
    Thank you! I was able to run the program, the ColorPAL stopped flashing colors. But I am not sure if the sensor is working now. How can I test that it is fine?
  • jacquelinevl03jacquelinevl03 Posts: 18
    I ran the flicker, mimic, sense, and transit programs and now the ColorPAL does not do anything. Could I have damaged the sensor? Or is it the programming?
  • Phil Pilgrim (PhiPi)Phil Pilgrim (PhiPi) Posts: 23,514
    Unless you plugged it in somewhere you shouldn't have, you didn't break it.

    -Phil
  • jacquelinevl03jacquelinevl03 Posts: 18

    When I ran the program I noticed I had the Pin connection in the wrong slot in the breadboard (right next to the place it should have been in. I did not connect it to the Voltage or Ground, it was just in a slot that had no connection.) so I connected it to the correct pin and it stopped flashing the color. Now it won't respond to programs like flicker, how can I check if the sensor is fine. Or maybe the code that was used made it stop flashing color completely, I am not sure.
    20170128_214453.jpg
    2304 x 1296 - 1M
    20170128_214445.jpg
    2304 x 1296 - 913K
    20170128_214432.jpg
    2304 x 1296 - 936K
  • Phil Pilgrim (PhiPi)Phil Pilgrim (PhiPi) Posts: 23,514
    edited 2017-01-29 07:07
    Your black wire is connected to Vin, rather than Vss. This would result in a reverse voltage powering the ColorPAL, which in all likelihood has fried it. But ... you may get lucky and not have any permanent damage. Fix your connection, try it, and see.

    -Phil
  • jacquelinevl03jacquelinevl03 Posts: 18
    edited 2017-01-29 18:57
    .
  • jacquelinevl03jacquelinevl03 Posts: 18
    Thank you so much!! The ColorPAL is reacting now!
  • ercoerco Posts: 20,254
    Hooray, PhiPi saves the day again! Always nice to see happy outcomes to these problems.
    Phil Pilgrim (PhiPi) wrote: »
    This would result in a reverse voltage powering the ColorPAL, which in all likelihood has fried it.

    Fry pork bellies, not Colorpals. Sensor lives matter!

Sign In or Register to comment.