Shop OBEX P1 Docs P2 Docs Learn Events
Gate Opener Controller/ More Add / Two RFID Card Readers / working on remote control — Parallax Forums

Gate Opener Controller/ More Add / Two RFID Card Readers / working on remote control

sam_sam_samsam_sam_sam Posts: 2,286
edited 2010-09-25 06:49 in Robotics
Here is one more Project that has taken a while to complete
It has a lot of point to point wiring

One Basic Stamp BoardParallax
One H25 Motor Controller Parallax
One Position Controller (Parallax..>>> modified Voids Warranty)
Two RFID Card Readers Parallax
One Battery Charging Board ( taken from the Mighty Board Controller Board which is DOA)
Two 2N2222A
One Relay
Six Resetable fuses


Pin 0 = input Opener re-tracked
Pin 1 = input N/A at this time
Pin 2 = input Start Switch By-Pass
Pin 4 = H25 Fan Cooling Relay/ LED Relay
Pin 7 = input/output from Position Controller

Pin9 =Card Reader1 Enable 1

Pin10 =Card Reader1 RX 1
Pin11 =Card Reader2 RX 2Pin12 =Card Reader2 Enable 2
More will come latterThe Remote Control

Sam

Post Edited (sam_sam_sam) : 4/24/2010 11:48:02 PM GMT

Comments

  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-04-03 01:18
    Here is the code for this project I will add more later but it is a working code and could be use the way it is now

    Thanks for any that you may have and all of your time finding them

    Sam
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-04-03 01:39
    Here is the story to why I did this project


    This GateOpener was at my bother house and one day it just stop working


    I call Mighty Mule and was told that a new controller board was $250.00


    A new Gate Opener is about $550.00


    I let me see if can find what happen to it


    Well I found a open Mosfet which I replaced and it started work again and work for about 3 months then one day it just stop working again but now the gate opener is at my mother house


    Now nether my bother nor I want to get out of the car to open the gate and do not want to buy a new Gate Opener


    I though well let me see if I can get a Parallax bought fix for the problem that I have with the gate


    the battery charging controller still work the Motor still worked


    A long time ago I had bought the H25 Motor Controller when they where on sale but I did not have a good enough project to use it


    One day before the Position Controller was on Parallax web site I ask about buy just the Position Controller


    The Parallax Sale Department was so nice to me that they gave it to me as a Christmas Gift which was very nice of them


    The Basic Stamp Board I already had






    Thanks for anyidea.gifthat you may have and all of your time finding them smile.gif




    Sam</A>
  • PJAllenPJAllen Banned Posts: 5,065
    edited 2010-04-03 16:50
    I always like it when people make stuff work again.

    [noparse][[/noparse]re. Top of Controller Board -- Definitely get some lug strips.· If you're interested, you can get fiber-epoxy board without any copper layer/ing (see McMaster-Carr, maybe Grainger).· It's a good prototyping material.· Watch the dust, just like with all printed circuit materials.]
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-04-03 19:57
    PJ

    Thanks for your comments about the boards that do not have the copper on them
    It came in hand to have the copper on both side which was need for some of the control boards pins because it made it easyer· to connect to the·main board to the next control board

    Where do you get· ·lug strips boards that have copper on both side that do not cost an arm and a leg to get

    The board that I used the cost of that board was $20.00 for a 6X9 board I had to cut some it to get to fit in the controller case

    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    ··Thanks for any·idea.gif·that you may have and all of your time finding them smile.gif

    ·
    ·
    ·
    ·
    Sam

    Post Edited (sam_sam_sam) : 4/3/2010 8:03:10 PM GMT
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-04-05 00:36
    I add more to this Project


    I did this a Project a while back that has few years now here is the link to it ( 4/30/2007 )

    http://forums.parallax.com/showthread.php?t=94132&highlight=sam_sam_sam

    To a Gate Opener (Basic Stamp had a mishap with Lighting and lost


    On my gate I NOW have two RFID Card Readers to the motor controller that is on it now


    What I am going to have the Basic Stamp control the RFID Card Readers and the Postion Controller


    So here is the code for it


    I have not test this code in full yet but the Postion Controller still work right so far so good


    Next weeken I hope to put in service

    Thanks for anyidea.gifthat you may have and all of your time finding them smile.gif




    Sam
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-04-24 23:14
    Here is an Up-Date

    Today I put the Gate Controller at the street and it work real good the motor runs a little bit slower than the one came with the Gate Opener but that OK

    I finished the sound and the two card readers and H25 Motor Controller with the Position Controller
    What I still have to work on is the Remote Control for the Gate Opener

    Here is the Up-Dated Code for this Project

    One note...>>>>> I have driven my wife crazy with this project being on the family room floor of our house for last two month this is where I do my programing at Late at Night

    She is so happy that I am done with most of it




    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    ·Now wanting to learn Spin· Thanks for any·idea.gif·that you may have and all of your time finding them smile.gif

    ·
    ·
    ·
    ·
    Sam

    Post Edited (sam_sam_sam) : 4/24/2010 11:42:03 PM GMT
  • Shawn LoweShawn Lowe Posts: 635
    edited 2010-04-26 18:56


    One note...>>>>> I have driven my wife crazy with this project being on the family room floor of our house for last two month this is where I do my programing at Late at Night

    She is so happy that I am done with most of it

    ·
    Sam- LOL! Well it's good you got the project working AND improved your marriage! tongue.gif

    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    Shawn Lowe


    When all else fails.....procrastinate!
  • MoskogMoskog Posts: 554
    edited 2010-05-29 12:20
    Sam

    I really enjoy reading about the way you always seems to make something useful out of the Basic Stamp, you are indeed my favourite Stamper!
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-05-29 13:52
    Thanks for your reply

    I try to come with a·fix to what ever·problem that·I am having at the time

    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    ·Now wanting to learn Spin· Thanks for any·idea.gif·that you may have and all of your time finding them smile.gif

    ·
    ·
    ·
    ·
    Sam
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-07-21 11:21
    Bad news it was struck by lighting a few days ago and it will not do any thing now

    I have not had time to troubleshoot what has happen to it

    This is the second time this has happen to this gate controller

    Down my street there about 5 or 6 gate that are not working after that Storm

    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    ·Now wanting to learn Spin· Thanks for any·idea.gif·that you may have and all of your time finding them smile.gif

    ·
    ·
    ·
    ·
    Sam
  • MoskogMoskog Posts: 554
    edited 2010-07-21 12:42
    Thats real bad, Sam. Lightning does have a very bad habit by always trying to break down what we build up. And you can't ask it to be nice either.

    If you troubleshoot it please tell us what things you need to replace.

    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔


    KjellO
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-07-24 13:57
    Bad new get even worst

    Note parts where test with a working Basic Stamp Board

    Basic Stamp Chip fried

    Basic Stamp Board fried ComputerDose NOTsee Basic Stamp Board with a good Basic Stamp Chip


    Power transformer fried ? I will take it a part to see what happen to it


    Memory Chip ok ? Did not try to program with this chip yet


    Need to order a new Basic Stamp Board Kit

    I still do not know what else got fried untilI get the new board kit
    I will you posted what else happen to it


    Now wanting to learn Spin Thanks for any that you may have and all of your time finding them Sam
  • abbtechabbtech Posts: 2
    edited 2010-07-25 08:23
    Nice work Sam,

    Good luck on the lightning repair. Looks like there are some MOVs on the inputs? Did they explode trying to save the circuit or was there no visible damage to them?
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-07-25 21:38
    Abbtech

    Looks like there are some MOVs on the inputs? Did they explode trying to save the circuit or was there no visible damage to them?

    There where none· MOVs· on anything

    One of the following or all four of them ....>>>>··The Brown Out Detector· or one of the 2N3904· or 2N3906 fried as well· ? ? ? ?

    but the last time I try to repair a· Basic Stamp Board· the traces lift off the board That is why I am just going to order a new board



    ▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔▔
    ·Now wanting to learn Spin· Thanks for any·idea.gif·that you may have and all of your time finding them smile.gif

    ·
    ·
    ·
    ·
    Sam

    Post Edited (sam_sam_sam) : 7/25/2010 9:45:03 PM GMT
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-08-22 13:51
    Up-Date

    It even gets worse it look like the Position Controller took a hit as well

    Some good new about the Power Transformer it look like the Temp fuse open in the
    Transformer and the power LED also took a hit

    More Latter if I can get it up and running again
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-09-11 16:56
    :) Thump Up maybe :):):) Thump Up

    The Gate Opener is back working again BUT need a new Power transformer

    Position Controller >>>> took a hit would NOT send commands to H25 Motor Controller >>> New Board
    Basic Stamp Board >>>> took a hit >>> New Board Kit
    Basic Stamp Chip >>>>> took a hit >>> New
    Power transformer >>>> took a hit >>>> Replaced LED and by passed Fuse transformer over heats BIG TIME :skull: :skull::skull: >>>>>> BAD
    H25 Motor Controller >>>> ????? more testing need to be done Replaced with new one
    Memory Chip OK >>>> ???? Did not try to program with this chip yet

    My Wife is so HAPPY that the Gate Opener is working again but now it a :roll: once I get a Power transformer will back on track

    I just got the new tranformer in today and so far so good we will see if this works or not
  • sam_sam_samsam_sam_sam Posts: 2,286
    edited 2010-09-25 06:49
    UpDate on Repair

    The Gate Opener is back working again

    Memory Chip OK >>>> Programing works OK
    Basic Stamp Board >>>> took a hit >>> Replaced low voltage detector , 2N3904, 2N3906 board works again :):) >> New board on gate opener
    Basic Stamp Chip >>>>> took a hit >>> Bad>>>IC chip shorted pull Power Supply down to 3 Volts :skull: :skull: >>New one on gate opener
    Power transformer >>>> took a hit >>>> Transformer over heats BIG TIME will not use again :skull: :skull::skull: >>>>>> BAD
    Position Controller >>>> took a hit >>>> would NOT send commands to H25 Motor Controller >>> New Board
    H25 Motor Controller >>>> ????? more testing need to be done >>>> Replaced with new one

    My Wife is so HAPPY that the Gate Opener is working again :):):) Thump Up

    /QUOTE]
Sign In or Register to comment.