Search:

Roger that ElectricAye. Sounds like you have your hands full. Just to let you know, I was offering more than just sheet metal enclosure help. I also have the tooling for plastic enclosures. Injection...

Yeah, I know what you mean Carl. Guess we had nothing rock solid to contribute....

ElectricAye, I can visualize your idea of an erector set type enclosure with removable panels with the cutouts...

Good job Carl. Looks very professional. I like your method of assembly but since I have a machine shop complete with a nice compliment of sheet metal working equipment and tools, I make my own...

Thank you Tim for the links.

I will check those site's, although I was hoping for the schematic here in the forums. And the search goes on....

Twisted Pair....

Thanks for the help Kelvin.

The Schematic was of a standalone unit that was used for testing servo's. If I could remember the subject & who posted the question regarding motors versus servo's etc...

Thanks for the links Brian.

I was really hoping to find the servo/tester schematic that was submitted here on one of the forums. I know that it's just a matter of time before it's found.
...

Looking for a schematic of a servo tester/exerciser that was submitted on one of the forums by means of a reply to someone who posted a question about servo vs stepper motors etc. The circuit had a...

Cool....I'm glad that you got it working. Before starting a project, I always draw a diagram first and after double checking that everything is correct on paper, I then will build and assemble the...

Could also be a low battery. How were you powering the set up on the first board that you were using ? Try a new battery....



TwistedPair....

Got a diagram of how you have it connected ? A common mistake on stand alone micro's is the ground wire. It must be connected to the ground for the entire circuit & hardware, also how are you...

Paintballer,

Your code & hardware works on the factory Basic Stamp board but not on the non-Parallax board. What are you using for the second Board ? I assume that the stand alone micro was...

Here is more DS1620 information for you Dave. MSDTech also posted the link to this information as well.



TwistedPair....

Your Stamp Pin assignments will vary depending on how your Code is written. I haven't seen the spreadsheet that you mentioned but here is a Data Sheet for the DS1620. Maybe this will help you.

...

Thanks guy's for the sites. I'll look them over to see if there is anything I can use for my project. I've looked the net over for many countless hours with no luck as of yet. Looks like I might end...

Anyone know where to find small spur and face/crown gears ? 3/4" OD or smaller is the size that I'm looking for.

Thanks,

Twisted Pair....

Tommy,

I'm running the DS1302 in an IC socket and have been for quite a while now with extreme accuracy. The crystal is from Parallax, and is soldered very close to the pins of the socket with...

Unsoundcode,
Once the setpoint is reached, the controller will maintain the temp usually within a few degrees above or below the setpoint. The injection barrel has a 1/2" wall thickness so it is...

PJ,
That is correct. The thermocouple is also routed through the DB9. The DB9 added a nice visual way to exit the enclosure although the wiring could have just been routed through a rubber grommet...

Anyone have any thoughts or new ideas regarding my project ?

Twisted Pair....

Thanks Sam....

Twisted Pair....

The Temperature Controller use's two Solid State Relays in unison to control two heater bands in·a Molded injection machine. Although this project was for a particular use, it could be adapted for a...

Morrolan,

Did you get what you needed ?

Twisted Pair....

Thank you Mike....


Twisted Pair....

Hello everyone, I have a question regarding what the capacitor's on the input and output side's of the voltage regulator do. I have looked over the regulators data sheet and still haven't come to any...

Morrolan,

Try this.

Twisted Pair....


Post Edited (Twisted Pair) : 3/7/2008 3:18:17 AM GMT